Question about Panasonic KX-T7453 Corded Phone

1 Answer

No longer have access to making outbound calls after programming phone numbers

After following the instructions in the manual on page 18 for the model phone I have I an unable to make outbound calls on the "CO" lines that I have programmed the phone numbers on. For instance, I have programmed a phone number on CO 1 and now when I choose this line as the one I want to pick up and dial out on I am unable to do so. I also have noticed that it doesn't receive inbound calls either! Please help!

Posted by on

  • stevitaylor
    stevitaylor May 04, 2012

    I have the exact same problem with a Panasonic KX-T7220!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

[Program] 99, [CO-01], 0, 01, [Store]

Posted on Jun 25, 2008

  • stevitaylor
    stevitaylor May 07, 2012

    Eric, you rock!

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My phone was showing caller ID but last evening it only showed incoming call. How do I get my caller ID to work? IT is working on my cord phone?


Hi
I would advise you to go through the instructions in the manual again very carefully to make sure you set it correctly, and then test it using a known number.
Caller ID is not infallible and will not display a number if the caller uses "number withheld" or in many cases if it is an overseas call.
Hope this is helpful, if so would you please register that with Fixya
Cheers

Dec 03, 2014 | Phones

1 Answer

Where is the Caller ID for Outbound calls programmed?


Have you resolved this yet? If your CO connection is analog, it's done by your telco. If you have a PRI (T1), then it's in your system's configuration.

Jun 26, 2014 | Nortel Phones

1 Answer

Call-forwarding


This is a Toll Fraud issue that is being access through an individual mailbox that has Outbound Transfer turned on in the COS. Someone will need to access the voice mail through the LAN interface and access the VMS GUI to manipulate the COS to turn off the Outbound Transfer in COS 1. This is a known issue on the Norstar related VMS\'s.

Feb 19, 2014 | Nortel Networks Business Series Terminal...

1 Answer

Lost my pin to access messages. The phone model is a Panasonic cordless Model TGA542AL.


Which model of Uniden phone do you have? Do you remember the PIN that you have programmed into the phone? (If the PIN is not set, you can't access the answering system remotely. The Uniden phones that I know don't have a default PIN.) 

For the DCT648, to access the messages remotely, dial your phone number and wait for the system to answer. Press 0 followed by your 2 digit PIN (within 2 seconds of pressing zero) while the greeting is playing. To play back all of the messages, press 0 2. If the unit is off, then you need to press 0 followed by your PIN (within 2 seconds) after 10 rings and the beep. Press 0 6 to turn on the unit. 

Other Uniden phones use a 4 digit PIN. On the DECT1080, when the greeting plays, press * followed by the PIN. Then press 01 to play back the messages. 

Uniden phone manuals are available at the product page (start at http://www.uniden.com and search for your phone) or from the Support page ( http://www.uniden.com/scat/cordlessphones_mnl ) . On the support page, you will need to use the drop down menu to change the type of phone (if you have a DECT phone) and then search through the pages. The manuals are listed in numerical and alphabetical order. One manual will cover several phones if the phone supports multiple handsets. So ignore the number after the dash if you can't find your exact manual. 

If you add a comment with your phone's model number, I'll be glad to check the specifics for accessing the answering system for you. 

I hope this helps. 

Aug 30, 2011 | Panasonic Phones

1 Answer

I have got a Panasonic KX-TG7220NL. Cannot change from pulse back to tone. How to do that?


First of all, here is the main ONLINE SUPPORT page for your model:

http://www2.panasonic.com/consumer-electronics/support/Phones-Fax/Telephones/Bluetooth-Enabled-Systems/Operating-Instructions/model.KX-TG7622B.O#ts


And here is a direct link to the ONLINE USER'S MANUAL for that model:

http://service.us.panasonic.com/OPERMANPDF/KXTG7622-MUL.PDF


To view the Support Page or the Owner's Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and highlighted text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual.

You may need ADOBE READER installed on your computer to read PDF documents.
You can download this free at WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer.

See page 18 of the manual for detailed instructions on how to switch between TONE and PULSE dialing. Basically it reads as follows:

Dialing mode

If you cannot make calls, change this setting according to your telephone line service.
The default setting is "Tone".
"Tone": For tone dial service.
"Pulse": For rotary/pulse dial service.

1 - MENU # 120

2 - Use UP / DOWN arrow keys to select the desired setting.

3 - Select SAVE and then OFF


I hope that was helpful to you, good luck and take care.

Joe.

Aug 26, 2011 | Phones

1 Answer

Can we make it so the phone can receive calls but not make out going calls?


You can, but you need access to Installer level programming. I'm not going to give you detailed instructions here, because any fool can do the reverse and UNrestrict a phone with the same instructions, but system program 500 and 501 sets day and night restrictions on a phone. Setting the COS to 7 lets the phone dial 0, intercom, and, by programming, System speed dial numbers.
COS 8 allows Operator only (internal operator).

By building tables, you can actually program different restrictions and exceptions for COS 2-6. There's a fairly comprehensive discussion in the Panasonic Features Manual of your TD 816/1232 manual.

Carl

Feb 18, 2011 | Panasonic KX-T7431 Corded Phone

1 Answer

How to page


You will need the page codes if you use the feature to page select groups. One softkey will have PGE written above it when the phone is in a mode that can page. This is the Page key (the second softkey on most of the phones in the group).

To make a page announcement to phones or external speakers: Lift the handset, press the extension and then enter a paging access code.

To make a group page, Press Group Page and then the group code or press extension + #31 and the zone number .

To make an All Call Page

1. With the handset off-hook, press All Call Page
...or dial #30. This pages all telephones in the All Call Page Group but, depending
on system programming, you may or may not page external speakers.
2. Make your announcement then hang up.

To make an Emergency Page

1. To make an Emergency Page, lift the handset off-hook, dial #37.
2. To make an Emergency Page to a group, lift the handset off-hook, dial #38 and
enter the Group number.

The manuals for all Toshiba phones
are here: http://www.telecom.toshiba.com/Telephone_Systems_Resources/User_Guides/ . The DKT3010SD is part of the IPT2000/3000 series phones; the direct URL for the manual is http://www.telecom.toshiba.com/Telephone_Systems_Resources/User_Guides/pdf/_new/Strata_CIX_Strata_CTX_User_Guide_IPT2000_and_IPT3000_Series_Telephones.pdf .

I hope this helps.

Cindy Wells

Jan 31, 2011 | Toshiba DKT3010SD Corded Phone

2 Answers

How do I change the voice mail prompts to forward to cell phone.


I can get you to the right place, maybe. You are better off calling the installer who set this up to see what method he used.

http://www.public.carl.airpost.net/TVA/210_TVA_08-01.pdf

Assuming you have a TDA/TVA system, pages 45-50 describe how it was probably installed. WIth personal custom service, it is the easiest one to make changes on. We usually set it up as an ICD group, which gives everyone 3 digit access from everywhere, but you have to have access to the system programming to change numbers.

Carl

May 06, 2009 | Panasonic KX-T7630 Corded Phone

1 Answer

Need to forward a cal to an outline phone number using Partner 18


YOU CAN DIAL A CODE ON ANY PHONE *72 AND THEN FOLLOW THE INSTRUCTIONS THAT FOLLOWS

Mar 31, 2009 | Avaya Corded Phone avaparp18d

3 Answers

Instructions manual in English


Hello,

Find the product number at the top left of the bar code on the bottom of your base unit.

Finding the product name/model number:
  1. Look on the bottom of your phone for the serial number sticker.
    (If you have a multi-handset unit, it will be on the main base.)
  2. The product name is in the top left corner of the sticker, above the bar code:
Once you have the specific model number go to this web page and follow the list down until you find your model and follow the list down until you find your model, click on product details. You will see the link to the manual at the top right of the model page, which is a PDF file. You can get the latest version of Acrobat PDF Reader at this location here..

Otherwise, if you would send me the model number as described above in a comment using the box below I will post a direct link for you.

Regards,
Worldvet

Jun 04, 2008 | Uniden Cordless Phone

Not finding what you are looking for?
Panasonic KX-T7453 Corded Phone Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Phones Experts

kakima

Level 3 Expert

96576 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

guyvstewart

Level 2 Expert

82 Answers

Are you a Panasonic Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...