Question about RCA P52926 52" Rear Projection Television

1 Answer

Chasis number thanks for your quick response. You asked for the chassis number for my suspected problem. I'm not sure if you received my post (I'm new to this site). Just in case, the chassis # is PTK169PDBS

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 149 Answers

This is same ctc169 check for separated power supply for convergence some times 2 wiress goin from main chassis to convergence board red and black are intermiten check for that but you mention that only show menu. select tv and check for tv signal or video imput if you dont have video you have convergence problem and some thing else

Posted on Apr 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I thought the lamp had gone out on my Mitsubishi WD-62825G but after replacing the bulb (2 times) I figure it?s something more as the red light comes on instead of the TV. Called out A+ as they said they...


if is not under warranty then you should buy a new tv. i had 3 lamps, 1 light engine, and they are currently rebuilding the chasis for the second time. i got my tv in 12/04 and got the 5 yearextended warranty THANK GOD! they are spending more time/money to keep repairing this pos than its worth. they could have gotten me a new model and saved everone the hassle. i would not recommend repairing it.
good luck

Jun 26, 2009 | Mitsubishi WD-62725 62" Rear Projection...

1 Answer

Sony 57" dlp TV CONVERGENCE problem


You have to pull the chasis completly out the set. Make sure you know where all the wires go that u have to unplug. Also u may need to change open resistors near the convergence amplifiers.

Apr 23, 2009 | Projection Televisions

1 Answer

RCA model R61WH76 Chasis itc222 has 3 color curved band lines on


Your model doesnt have convergence ICs. You can get the replacement parts and free instructions on how to do the repair at the following link, just click on the contact us link on the lower left hand side of the website and tell them the model number and chassis they respond quickly.
http://servicemanuals.vstore.ca/

Apr 11, 2009 | RCA R61WH76 61" HDTV

2 Answers

Replacement STK numbers for convergence amps


This unit does not use the STK series convergence amps.The convergence power supply is what you need.I will provide that number for you after while.

Jan 19, 2009 | RCA P52960 52" Rear Projection Television

1 Answer

No Response to Problem


Sorry for the late response .....I was out of country on vacation......T.

Dec 04, 2008 | Hitachi 43UWX10B 43" Rear Projection...

1 Answer

HITACHI LCD


Hi,

Appreciate the direct "Ask Me".

Offhand without a specific model number or better yet a chassis number, I would be guessing that the blue being absent makes the green too pronounced. This being so on an LCD projection made by Hitachi would indicate probable fault with the light engine. You may want to reference this post that indicates Hitachi would supply the part for free. Incidentally, another post outlined how a user performed a DIY (do-it-yourself) workaround.

Hope this be of initial help/idea. Pls post back the model number or chassis number, how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

Nov 11, 2008 | Projection Televisions

3 Answers

Flashing timer light, cannot turn on tv


Press and hold "Device" and "Menu" buttons for six seconds and see if you then get a patter of flashes pertaining to the error codes... I would suspect one of the following codes:
12 No Error Detected
22 Recovery From Momentary Reset
32 Lamp Cover Open
33 Air Filter Cover Open
34 Lamp Abnormality
35 Chassis Fan Failure
36 Exhaust (Back Cover) Or Lamp Ballast Fan Failure
37 Engine (Dmd Or Lamp) Fan Failure
38 Excess Lamp Temperature
39 Excess Dmd Temperature
41 Short Detected
44 Dvi Cable (Between Chassis And Engine) Disconnected
Bill

Sep 26, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

About rca model r52wm24


Yes I know where you can get the signal board for your model. Go to the following link and leave them a email with your model and chassis number and let them know you need a signal board. They will respond back quickly. they have about any bopard you need for RCA they dont list them all, but inquire, and I am almost positive that they have one.Heres the link.
http://servicemanuals.vstore.ca/

Jul 29, 2008 | RCA R52WM24 52" HDTV Projection Television

1 Answer

Thank you for the quick response


Just leave them an email with your model number and they will post the correct kit for your model then send you an email, they have an extensive inventory and they dont list all their parts untill they have a request for them.

Jun 11, 2008 | Mitsubishi WS-65513 65" Rear Projection...

Not finding what you are looking for?
RCA P52926 52" Rear Projection Television Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...