Question about HP PSC 1410 All-In-One InkJet Printer

1 Answer

Alignment problems Hi, I changed the color cartridge of my printer and it started doing the alignment process, it printed the page and then I placed it to be scanned, but when the time came to press scan it did not work, so the process did not finish. Therefore, I cannot print because whenever I turn it on the alignment process starts again and I waste ink printing the page over and over. Should I throw this printer away? I will appreciate your help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

No dont throw it
hp is foolish it even happens with me ignore it

Posted on Apr 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, Wonder can you help my printer keeps printing off test page everytime it is turned on. this is only happening since i changed the cartridge, never did this before. thanks


Hi,

Your printer is printing alignment pages, because the cartridge alignment was not completed since you replaced them. Follow the below steps to complete alignment.

  1. Turn the printer OFF and then turn back ON.
  2. Wait until the alignment sheet prints out fully.
  3. Place the alignment test page over the scanner glass.
  4. Press start color scan button.
  5. The printer "power" light will start flashing, indication the alignment process.
  6. After the printer stops flashing, turn off and then ON the printer.It will not print any test pages further.
We need to run alignment test every-time while we replace ink cartridges.

Regards
Riztech

Nov 27, 2010 | HP Photosmart Premium C309A All-In-One...

1 Answer

The alignment both vertical and horizontal are off!


Title: How to Install/Change the Print Cartridge Document ID:HO46 Back To Answers Properties 1000 Color Jetprinter 1100 Color Jetprinter 2030 Color Jetprinter 2050 Color Jetprinter 2070 Color Jetprinter 3000 Color Jetprinter 3200 Color Jetprinter 5000 Color Jetprinter 5700 Color Jetprinter 5770 Photo Jetprinter 7000 Color Jetprinter 7200 Color Jetprinter Lexmark X63 Lexmark X73 Lexmark X83 Lexmark X84 Lexmark X85 Mac OS 8.6 Mac OS 9.x.x WinWriter 100 WinWriter 150c Z11 Color Jetprinter Z12 Color Jetprinter Z22 Color Jetprinter Z25 Color Jetprinter Z31 Color Jetprinter Z32 Color Jetprinter Z34 Color Jetprinter Z35 Color Jetprinter Z42 Color Jetprinter Z45 Color Jetprinter Z45se Color Jetprinter Z51 Color Jetprinter Z52 Color Jetprinter Z65 Color JetprinterHow to install or change the print cartridge; Microsoft Windows 95; Microsoft Windows Me; Microsoft Windows 3.1x
Solution Microsoft Windows 95/98/Me:
(Applies to all printers)

  1. Click Start, Programs, Lexmark Series.
  2. Click Lexmark Control Panel.
  3. Click Print Cartridge installation.
  4. Depending on which cartridges you are using and which printer model you have, select Install Color Cartridge or Install Black Cartridge or Install Photo Cartridge.
  5. Carefully remove the tape covering the printhead of the print cartridge. Important: Be sure to remove all of the tape. Do not touch the copper area on the back of the cartridge.
  6. Insert the print cartridge into the print cartridge carrier.
  7. Push the cartridge back until it clicks into place.

    • If the print cartridge moves loosely in the carrier, it is not locked into place. Repeat step 7.

  8. Click the appropriate Cartridge Installed option in the printer software.

    • If you choose to install a new print cartridge, you will be prompted to align your print cartridges. The printer will print a page with a bi-directional alignment pattern. Follow these steps to align the cartridges:

      1. On the printed test page, locate the number under the Bi-directional Alignment pattern that comes closest to forming a straight line.
      2. Enter the number as the Bi-directional Alignment setting in the Alignment Cartridge screen.
      3. Click OK.

  9. Close the front cover of the printer.

Dec 16, 2009 | Lexmark JetPrinter Z11 InkJet Color...

1 Answer

I changed the ink cartridges and now the alignment process cancel


hi

take out the cartrdiges
put them one by one,start wih putting the black and the color in their respective slots
wait for the printer to automatically print the alignment page,it might even ask you to put the alignment paper on the scanner bed to complete the alignment ,also you can print an alignment sheet from the computer by going to the prntr iconin the control panel's printer and faxes ,do a right click on the printer icon ,goto properties and click on printer preference.
and then click onmaitenance and print the alignment,i would insist on the automatic alignment

Jul 14, 2009 | HP PSC 2210 All-In-One InkJet Printer

1 Answer

HP PSC 1315 Prints test page every time printer is installed


Hi Jay,
This is mike, actually the problem is that that printer has not completed the aligning process, as a result the printer is printing the test page (Alignment page) every time when you turn it ON. So, I would suggest you to let the printer prints the alignment page and check whether the printer prints the page with all colors and it printed fine, once it is done, disconnect the USB cable behind the printer and then place the alignment page on the scanner glass by facing down the printed page downwards and press the scan button. This start the alignment process and the scanning process will be completed once the ON light is stop blinking. This will complete the alignment process.

Once done try to turn off and turn on the printer and check for the result. This should resolve the issue.

However, if the issue persist, then please revert back to me. Be sure that you use the HP genuine ink cartridges, not refilled nor re-manufacture.

Jun 20, 2009 | HP PSC 1315 All-In-One InkJet Printer

1 Answer

When I change the black ink cartridge, the alignment page and instruction page are printing out fine. When I place the alignment page on the glass as instructed and press 'ENTER', the printer gives a...


I just had the same issue (align page not detected).

We had just re-installed the empty color cartridge back into the printer (long story but basically we knew we could only print B/W).

The align page printout had a lot of empty spaces around the black lines. This is apparently where the color lines are supposed to print.

Without those color lines, the printer would not detect the align page as color is part of the alignment being done.

Since we only wanted black printouts, I pressed 'cancel' to stop the alignment process, and now we just hit the Black copy button and ignore the alignment prompt on the printer window.

The HP site (enter psc750 in product window) has some helpful ideas as to what the problem might also be. It could be the shipping tape is still on the new cartridge (and preventing the black or color from printing on the align sheets) etc.

Mar 20, 2009 | HP PSC 750 All-In-One InkJet Printer

1 Answer

WHEN I TURN ON THE PRINTER IT STARTS TO PRINT THE ALIGNMENT PAGE


Hi Mahdavi,

In HP PSC 1315 printer after replacing new Ink Cartridges the printer always prints Alignment test page every time you turn it ON.To resolve this problem you must complete the alignment process.

Steps

1.Turn the printer ON.
2.Once its ON, it will print the Alignment page. Place the page in the scanner bed correctly.
3.Then Press START SCAN button.
4.The power light will start blinking, wait until the power lights turns solid.
5.Now Alignment process is over.Discard the paper from scanner.
6.Turn the printer OFF and then ON, it will not print that page again.

Note:Please follow this steps every time when you replace the Cartridges.

Thanks
Rizwan
rizwan84tx@gmail.com

Dec 06, 2008 | HP PSC 1315 All-In-One InkJet Printer

1 Answer

In starting 1 page print


Hi,

I believe that after changing the ink cartridge you havent completed the alignment process.This Alignment test page will print everytime you turn the printer ON.To Complete the alignment follow my steps.

1.After turning the printer ON, wait untill the printer prints the Alignment test page.

2.Then place the alignment test paper on the scanner, facing down in a correct position.

3.Then press the Scan button(color) and wait untill the printer ON light stops flashing.

4.After the light stops flashing, take the paper out and the alignment process is completed.

Turn OFF and turn On the printer, it will not print the Test page again.try it and please let me know.Would really appreciate your rating for my solution.

Thanks
Riz.

Apr 15, 2008 | HP PSC 1315 All-In-One InkJet Printer

1 Answer

MY test page always prints


Hi,

I belive that after replacing the INk cartridges, you are experiancing this problem. The Alignment test sheet always prints everytime you turn on the printer, if u haven't completed the Alignment process.

To complete the Alignment process,
>>Once the printer finished printing the Alignmnet test sheet.
>> Place the Test sheet staright on the scanner glass facing down towards right hand corner.
>>Press the scan button(color), the Power ON light will start flashing, wait until it stops flashing.
>>Alignmnet process completed.


Thank You

Feb 09, 2008 | HP PSC 1315 All-In-One InkJet Printer

2 Answers

Aligning printer after new ink cartridge inserted


SOLUTION: Start the cartridge alignment by performing a series of button presses from the front panel of the product.
  • HP PSC 1200 and 1300 series:
    1. Turn on the HP PSC 1200 or 1300 series product.
    2. Disconnect the USB cable from the all-in-one.
    3. Press the sequence of front panel buttons below to start the print cartridge alignment process. The button-press sequence must be completed within ten seconds. It might take several tries to complete the sequence within ten seconds.
      1. Press and hold Cancel .
      2. While holding Cancel , press On .
      3. When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both buttons.
      4. Press Cancel again.
      5. Press Copies .
      6. Press Paper Type .
      7. Press Color Start Copy . The alignment page will begin printing. If the alignment page does not print, repeat the button-press sequence in this step.
    4. When the alignment page has printed, place the page face down on the scanner glass and press Scan . The alignment is complete when the On light stops blinking.
    5. Reconnect the USB cable.
CAUSE: This can occur if the cartridge alignment is canceled or times out without a valid print cartridge alignment stored in memory.

Oct 29, 2007 | HP PSC 1350v All-In-One InkJet Printer

Not finding what you are looking for?
HP PSC 1410 All-In-One InkJet Printer Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...