Question about Quantegy ADAT: ADAT: 60 Minutes ADAT (S-VHS) Tape

2 Answers

Write protection i want to remove write prottection to my flash drive

Posted by on

2 Answers

This is a switch to unlock the write protected on your storage media, you just have to look for it.

Posted on Oct 22, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 156 Answers

The link
THis will help you ...

Posted on Apr 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dvd write protection


Over the air broadcast has to contain a FLAG that makes it copy protected.

Nov 26, 2013 | Sony Blank Media

2 Answers

My sony mini hi-fi deck continue to tell me to i quote 'PUSH POWER;PROTECT' what do i do?plss help.


You PUSH the POWER control (OFF) because it is self protecting.

Generally speaking, an amp attempts to protect itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or
marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is
running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'nekkid'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Check for loose speaker connections at the speaker as another possible root cause for intermittent shutdown.

Sep 03, 2011 | Sony Blank Media

1 Answer

HOW TO REMOVE READ ONLY ON MY FLASH DRIVE?


Flash drives have a lockout on them.This is to prevent accidental erasure.Go to the store that sells these and have them show you how to unlock the drive.

Jun 18, 2011 | Kingston CDR-8CM Other

1 Answer

M getting protect on my stereo display


It is possible that your device is shutting off due to a short in the circuit. hence for protection the device is switching offf the powerr to the main circuits. You will need to check for the short , maybe outputs or drivers and disconnect, replace to confirm. since you have not mentioned the model I am not able to comment more. Good day

Aug 12, 2010 | Samsung Blank Media

1 Answer

Whenever i turn on my sony MHC-VX333 mini hi fi it flashes the message "push power protect"


Hello,
when it display push power,this indicate an instruction to push the power button. please do so

May 17, 2010 | Blank Media

1 Answer

Protective mode how do i fix it


sounds like you will have to get the audio ics replaced. it would be better for you to take it to someone with the tools to repair it. unless you have a solder kit handy..:)

Jul 01, 2009 | JVC Blank Media

2 Answers

My HT-TX75 DVD flashes a message


First thing to do is disconnect all your speakers at the back of the receiver, then turn it back on. If it does not go into protection, post a comment and I can walk you thru troubleshooting. If it still goes into protection, your unit needs to be serviced. Hope this helps

Jun 24, 2009 | Blank Media

1 Answer

"prot" error message on Alesis ADAT 16 bit recorder


I heated the mechanical sensor switch with a hair dryer. Probably caused a contact point to expand just enough to close the circuit. 

Dec 11, 2008 | Basf 938 DA-40 ADAT 16Bit format / Album...

1 Answer

Home theater


Check to make sure that your speakers' ohm rating matches the amp.
Also check every speaker connection carefully for stray strands, poor connections, etc.

Aug 22, 2008 | Blank Media

Not finding what you are looking for?
Blank Media Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Quantegy Blank Media Experts

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

sonny shoeria
sonny shoeria

Level 1 Expert

40 Answers

Are you a Quantegy Blank Media Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...