Question about Yamaha RX-V800 Receiver

1 Answer

Yamaha RX V800 w/ iTunes Airport Express

Hi. I hooked up my iTunes to the Yamaha via Airport Express. The music comes out fine in the front and side speakers but not the rear speakers nor the subwoofer. All spkrs function fine with just the amplifier. Apple support is baffled. I connect the Airport Express to the front AC jacks on the Yamaha. Any suggestions would be greatly appreciated?
Stan Rossiter kentrossiter@comcast.net

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 243 Answers

Thats cause your patch cable is mono get a stereo 3 ring connector.

Posted on Jun 14, 2008

  • Nathan Ayers
    Nathan Ayers Jun 14, 2008

    i had the exact same problem with this unit and reciever. Now it works great

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Connect Airport Express to Yamaha RX- V659


Since you're using a standard mini jack to double RCA cable, it's safe to assume you'll be sending line level signal into your reciever, so i think any of these audio inputs will do: AUX, CD, DVD, MD, TV.

Also try the inputs on the front of the unit (i guess they are meant to be used with a video camera or similar but they are designed for line level signals so it should be ok if you decide to use them).

Anyway, keep the source signal at a moderate
level when you test any of the inputs and raise it to a suitable level after you're sure it is coming thru well.

Normally, the AUX input is suitable for any AUXilliary signal source that puts out a line level signal, but if it is already being used, you may use other free inputs.

If you use TAPE or PHONO inputs, you should keep the signal level from the source a bit lower since these inputs will amplify the signal a bit more (especially the phono input which works with signals that are lower in level than the line signal).

I hope this helps.

Regards

3rq8 (Triarcuate)

Sep 06, 2009 | Yamaha RX-V659 Receiver

1 Answer

No picture from wii


The RX-V800 switches the various video signal types separately.
Since you are feeding S-Video to the TV the composite (yellow) input from your Wii is not going anywhere.
If you cant get S-Video output from the Wii then I'd suggest a simple Composite to S-video adaptor plug ($5 say). It worked for me with a Game Cube.
Cheers
BJ

Mar 19, 2009 | Yamaha RX-V800 Receiver

1 Answer

Config Problems After Repair


Sounds like they centre has configured your speakers to "none". You need to hook it up to a tV or monitor and go through the menu to "speaker settings" and make sure you select either "sml" or "lrg" for the speaker type. Also ensure on the LFE settings that you select either "swoofr" or "both."

Nov 02, 2008 | Yamaha RX-V800 Receiver

1 Answer

Yamaha rx-v800 remote control's damaged


it can be accessed via the main unit controls but you need to go through your manuals. Maybe you can get your remote repaired still... maybe not badly damaged caused by corrosion.

redrivera0314@yahoo.com

Feb 04, 2008 | Yamaha RX-V800 Receiver

2 Answers

Yamaha RX-V800 - No audio on left and right channels


I too am experiencing this problem.... and my receiver is only 5 months old. Its a RX-V661

Oct 30, 2007 | Yamaha RX-V2500 Receiver

1 Answer

Problem in yamaha rx v800


Hello!!! Are you electronic technician? You should see the transistors Q22A, Q22C, Q19C e Q19A and its drivers on Main Board. All the best, Rasgador

Aug 03, 2007 | Yamaha RX-V800 Receiver

1 Answer

Problem in Yamaha rx -v 8000


your system goes on auto protect mode. it can be repaired even without the shcematics if this is the only problem.

what particular module is he asking for?

Jul 29, 2007 | Yamaha RX-V800 Receiver

2 Answers

Rx-v800 shuts off after few seconds


Hi, You should try to see, on main board, the ground G2(TP00385), just to make sure if the screw is too tight. Its location on Schematic Diagram (Main) is E8. All the best, Rasgador

Oct 27, 2006 | Yamaha RX-V800 Receiver

Not finding what you are looking for?
Yamaha RX-V800 Receiver Logo

Related Topics:

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio & Video Receivers Experts

Larry Stiles
Larry Stiles

Level 2 Expert

286 Answers

jonpoint

Level 1 Expert

4 Answers

Are you a Yamaha Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...