Question about Sony FD Trinitron WEGA KV-32FS100 32" TV

1 Answer

Picture went side wave and stay that way

I check everything on the contol in back it must have something with hoz hold or teanformer but did not know which to buy.

Posted by on

  • Clifford Hardy
    Clifford Hardy May 11, 2010

    are there any adjustments on it like hoz hold?

×

1 Answer

I had that problem with a sony 32 inch. One day I hit the top and it corrected itself. Sometimes it the tv is on for a while the picture will unravel itself. Strange set. Right now it is working but some of the color is not right.

Posted on Apr 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sharp TV model #25E-S40 picture gets smaller, then returns to full screen


from side or up an down if up and down vert. side to side hoz.

Jun 23, 2010 | Standard (CRT) Televisions

1 Answer

No picture or sound, high pitched noise


hoz out off sny or fly back is bad or hoz out put bad

Jun 23, 2010 | Standard (CRT) Televisions

1 Answer

My proscan tv went into wide screen....everything shows up bigger. how do I get it back to normal? By wide screen, I mean if there are 2 people sitting at a table talking on screen at opposite sides of...


It sounds like you accidentally enabled a zoom feature or something similar.

Most remote controls should have a clearly labeled "zoom" button or a "picture size" option. If not, go into your TV's menu and look for something zoom related.

If this doesn't work, just go ahead and toy around in your TV's menu. I strongly suggest writing down the default settings so you can go back to them if you screw something up.

Good luck!

Aug 27, 2009 | Proscan Standard (CRT) Televisions

1 Answer

VIDEO TAPE WHEN PLAYED WAVE AT THE TOP OF THE TV SCREEN


This is a common problem usually seen when playing copy protected tapes. The part of the picture affected is normally off the top of the screen. Sometimes the problem is also due to the VCR itself and differences in tapes. It's also possible for the TV itself to be causing this, although you would probably also notice this flag-waving (that's what it's called) on regular TV viewing if that were true.

Sometimes increasing the height of the picture can push the affected area off the top again. But this can also cause you to lose part of the picture you want. Also, the height adjustment may be difficult to find as it's not something normally used. On some TV's it's a small pot somewhere on the board, but most newer sets have electronic adjustments through a service menu that you need to know how to access.

I'd suggest trying another VCR first and play one of the tapes you know shows the trouble. That might be all it takes. Then consider trying to increase the picture height if it's just a small bit at the top of the screen.

Mar 12, 2009 | Zenith B25A11Z 25" TV

1 Answer

Blank screen on sony trinitron tv


The problem with this model is the large parts due to poor wave soldering. Locate the transistor Q605. Using a small wattage soldering iron melt the solder and add a little solder to all the large parts in the area. Small wattage = 15 to 30 watt. Stay away from the surface mounts they are not the problem. I resoldered the following: D647
Q605 C690 D645 D620 R691 Q691
These parts are located on the main board, the one the power cord connects to. Carefully press the clip on the left side of the board (as you look at it from the rear of the tv) carefully pull the main board back and out of the rails. You will find the parts on the right side of the main board about 2 inches over 2 inches down.

Dec 30, 2007 | Sony FD Trinitron WEGA KV-27FS100 27" TV

4 Answers

Rca 32v434t


went in the menu and blocked the panel buttons on accident

Oct 13, 2007 | RCA 32V550T 32" TV

1 Answer

Jvc television


picture on tv started waving in & out

 

normally this problem is due to main filter capacitor failure in tv which is located in power supply.it becomes dry after few years

 

you can also check for normal voltage at input to your home.

hope this will help

good luck.

 

 

Oct 12, 2007 | Standard (CRT) Televisions

1 Answer

Sanyo DS25390


it looks like a capacitor problem in power supply circuit. the humming and waving of the picture is caused by a faulty filter capacitor in the power supply circuit. have it check and replaced if found faulty. good luck!

Apr 07, 2007 | Sanyo DS25390 TV

1 Answer

Blue wave shadowing


The convergence Ics need replaced. In Hitachi, resistors and sometimes a coil needs replaced as well. The convergence/deflection PCB is available, but, the cost of that board is higher than having a servicer come to your home and repair the unit to component level. If you are not familar with this circuit, then call a servicer. Have them replace both ICs not just one. Make sure they are repairing to component level and not replacing the board. Hope this helps.

Feb 08, 2007 | Hitachi 43FDX01B TV

Not finding what you are looking for?
Sony FD Trinitron WEGA KV-32FS100 32" TV Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68352 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you a Sony Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...