Could use a good diagram or repair instructions for putting trigger section and housing back together.
HI, I found something on amazon. here: Crossman Air Guns Model 760 Pumpmaster Owner Manual English spanish... . I hope I have helped. cheers
The trick to assembling the trigger mechanism is to assemble the trigger parts on the left half of the receiver. This will leave the v shapped spring hanging out the bottom of the trigger guard. I assembled the barrel to the right side of the receiver and then but the two halves together. loosely attached the halves with the two long screws. I then used a jewlers screw driver to work and hold the end of the V spring behind of the safety button hole. At this point I inserted the safty button into the hole as I gradually removed the screw driver. Then clamped down the attachment screws.
I spent some 2 hours figuring this trigger assembly out and another half hour putting it together. The biggest mystery was the use of the L shapped part. It ends up being assembled to the trigger pin. the cleat catching the back of the trigger and the long side of the L laying against the left side of the receiver (pointing up). The small tention spring ingages the back of this L shapped part (just above where the cleat ingages the trigger) and the other end of the spring ( the straight end) rests against the bottom of the receiver.
Here is a link to manuals and exploded views.
http://www.crosman.com/airguns/service/manuals/crosman-rifles
There's an exploded view available on the crosman website.
That's how I fixed mine.
http://www.crosman.com/pdf/manuals/C760-EVP%20&%20PL2.pdf
Hope that helps :)
Http://www.fotolode.com/images/Rapidfirex/crosmanpumpmaster760assembly.jpg
Thanks for the answers here. With the descriptions and photos, I was able to get my old 760C back together. Turns out all it needed was some oil in the pump chamber (just like the little sticker says..."3 drops". Ha!) But taking it apart gave me a good chance to clean and oil everything. Plenty of crud in there from the last 20+ years. It's back together and shooting nicely.
I followed j-momkelly's instructions on the trigger assembly with one change. When reassembling the trigger, I put the safety button in, and used the spring to hold it in place. As long as the big side of the button (left side of the receiver) was flush with the plastic, it held in place nice and tight as well as straight. Then the left and right sides of the receiver went together nicely without too much coaxing. The exploded view on the crosman sites above helped immensely as well.
Did you try to get the diagram from www.crossman.com?
I could also use a good diagram or repair instructions for putting trigger section and housing back together. Gun is about 30 years old.
Hi my rifle isnt a crossman so dont know if you can help its a umarex 850 airmagnum
Its real easy... I took mine apart and learned how to assemble it within 10 minutes. Look at the pic on google!
Try this site
http://www.crosman.com/2004/pdf/manualarchive/C760CLIP-EVP%20&%20PL%201.pdf
I would like to know if anyone out there knows how to assemble a crosman 1088 pellet gun? email me at [email protected]
48,984 views
Usually answered in minutes!
MY OLD FAITHFULL POWERMASTER 760 WOULDN'T HOLD AIR CHARGE I REMOVED ALL THE SCREWS ON THE RECIEVER HOUSING AND PROCEEDED TO INVESTIGATE. THATS WHEN THE PROBLEM DEVELOPED. I NEED TO FIND A SCEMATIC DRAWING TO REASSEMBLE IT. ALSO NEED A PARTS KIT TO RESTORE THE GUN IF THEY ARE AVAILIBLE. I KNOW I COULD BUY A NEW ONE FOR UNDER $40, BUT THIS ONES ONLY 37 YEARS OLD AND HAS BEEN WORKING GREAT UNTIL THIS VERY ABRUPT FAILIER.
reassembling a crosman 760 trigger section
Mine would not fire after being pumped up so I took apart but in doing so parts just fell on the table I cleaned everything and now need a diagram to put it all back together. I would appreciate any help, thank you
i took my 760 apart to clean it and i dont know how to put it back together but i need a clear enlarged diagram to beable to figure it out can you help???
son inlaw took triger out i dont now how to get it back in the fifle properly
how to put a 760 crosman trigger back togeter
I can't put my crossman 760 pumpmaster trigger assemble back together do you have any diagrams...???????
need diagram of Crosman Powermaster 760 BB Repeater /.177 pellet
Having trouble finding where spring goes back - a diagram would be very helpful
Thanks
trigger and spring need to be replaced.itook gun apart to clean and unclog
the spring is off and it wont let me fore the trigger??
need to reassemble pumpmaster 760
reassemble pumpmaster 760
i cant put it back together
I have the same problem
I have a prpblem reassembling my 760 air rifle
i have a crossman pumpmaster 760 and cant get it back together
need to rebuild it
trigger fell out to fast for me to see how to put it back!!! HELP!!
my crosman .177 cal. keeps losing air and i'd like to know how to fix it and restore it to its original power
reassembling crosman 760 pumpmaster airgun
I am having trouble reassembling the trigger spring on a crosman 760 also.
i tried to take appart my gun but dont know how to put together.
can't seem to put the trigger assembly back. can someone send me a diagram? thanks
can't reassemble
cant put it back together
Tyhe barrell is not broken, but it is twisted ( the site is misplaced)
I took apart my 760 pumpmaster .177 caliber pellet/BB pepeater and now i have some pieces i am not sure where they go if some one could help me that would be great
I have a 760 pumpmaster .177 pellet/BB repeater and I took it apart but now i dont know how to put it back together if any one could help me on how to put it back together that would be very apprecated
I need to resemble my 760 pumpmaster, my trigger and spring, Can anybody HELP ME?
need to locate parts number for missing front sight on crosman 760-D pumpmaster
×