Question about Ricoh Aficio CL1000N Printer

1 Answer

Ricoh CL100N with a SC 310 code

Can anyone tell me what this code signifies and how to clear it?

Billy Walker

Posted by on


1 Answer

Replace the PCU cartridge

Posted on Jul 18, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Hello and welcome to JA!!!
Billy :

I'm Billy and i will assist you with this.
Billy :

The codes you have (the ones not interpreted) mean the following:
Billy :

p1351: glow relay circuit faulty, p1586: power supply to rail sensor, air mass meter, EGR valve: voltage too low.
Billy :

These problems are the ones causing the no start issue...........
Billy :

I will first list the fault details:
Billy :Engine management ECU BOSCH EDC16C34Fault codeP1586After sales description of the fault codeSupply of the rail pressure sensor, the flowmeter and the EGR valve copy : Supply voltage too lowRectification priority1Description of the diagnosticsThe supply common to the pressure sensor of the fuel high pressure common injection rail, to the flowmeter and to the EGR valve copy is lower than 4,7 V for 150 msConditions of activation of the diagnosticsConsult the associated contexts for the Pcode forwarding conditionsConditions of disappearance of the faultSwitching on of the ignitionDown-grade modes if fault presentDefault value for the air flow as a function of the engine speed and of the flow injectedInhibiting of the diagnostics and air flow sensor plausibilityUse of the flow calculatedCut of all the actuators : EGR butterfly ( Turbocharger air cooler ) ; EGR electrovalve ; Bypass valve ( Intake air heater ) In all operating modesSwitching on of the warning light and/or warning messageWarning lamp MILSymptoms ( Possible customer complaints )Jerking/stallingLack of powerStarting problemSuspect areasThe sensors sharing the power supply are as followsElectrical harnessEngine management ECU (internal failure, supply, ...)Billy :Fault codeP1351After sales description of the fault codePre-heating relay circuit : Coherence ; Relay supplied and glow plugs not suppliedRectification priority1Description of the diagnosticsThe information from the preheating control unit indicates that the relay is open even though the ECU commands the closing of the relay for 2 secondsConditions of activation of the diagnosticsConsult the associated contexts for the Pcode forwarding conditionsConditions of disappearance of the faultOn switching onDown-grade modes if fault present-Switching on of the warning light and/or warning message-Symptoms ( Possible customer complaints )Lack of powerNoiseJerking/stallingStarting problemSuspect areasGlow plugElectrical harnessPre-postheating relaysBilly :

And now, the most probable reason for your problem, would be faulty wiring.
Billy :

So i suggest that you check the wiring harness thoroughly, and the fuse boxes (connectors, fuses etc.....)
Billy :

As these are the most probable culprits.
Billy :

It could be a faulty ECU (engine control unit), however, i think that faulty wiring is the most likely cause.......
Billy :

Billy :

JACUSTOMER-jxbcz9cx- :

on further diagnostics the engine start permission is off does this point to anything

Sep 11, 2012 | Audi A4 Cars & Trucks

1 Answer

Dodge dynasty flash code

First code is 12, that just signifies the beginning of telling you codes. Sometimes means that the battery has recently been disconnected or dead. Next code is 22. I believe that is for coolant temp sensor, either failure or because someone unhooked it to set the timing. Unhooking the coolant sensor tells the computer to go to basic ignition timing. Usually about 10 or 12 degrees. 3rd code is 55 and only signifies "end of codes". No real codes except 22. If that code is there because someone set the timing then it will automatically erase itself after 20 to 40 start, run cycles. About a week.

Hope this helps

Mar 17, 2012 | Dodge Vehicle Parts & Accessories

1 Answer

Anyone have the telewest codes for 13/03/2009

00= aa b7 d1 d9 ce 8e 83 af
01= a3 eb ec 07 d6 49 d2 eb


Mar 13, 2009 | StarView SV211K 2-port KVM...

5 Answers

Assembling seat of chicco dj baby walker

Possibly the worst instructions I have ever seen! However, I got it in the end. Reference the manual and follow these instructions. The padded seat folds over the the rigid backrest (c) (don't do this yet!). Start by dropping the front 2 rings through the slots, then, put your finger through the ring underneath the walker and pull (quite hard) until it comes right through and folds over so it can't pull back out. The seam of the padded seat fits into the groove where the ring slots are. repeat this for the next 2 and it should work itself out from there. Hope that helps!

Feb 06, 2009 | Galt America Baby Walker Push-Along Hand...

4 Answers

Minolta CF900 Photocopier

CODE C0900, DOES NOT PASS COPY, FIERY FRONT COVER BROKEN OFF AND VERY DIRTY, also you may want to try and look at the 3rd drawer lift perheps there's somthing blocking it

Aug 29, 2007 | Konica Minolta DiALTA CF910 Copier

Not finding what you are looking for?
Ricoh Aficio CL1000N Printer Logo

Related Topics:

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1297 Answers


Level 2 Expert

398 Answers


Level 1 Expert

67 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides