Question about Baumatic 23 in. BDW9 Built-in Dishwasher

1 Answer

My left hand side door cord has broken, how much of the machine do I need to take apart? do I need to pull the machine from under the counter top?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 269 Answers

Hello,

Yes you will have to move from under worktop and then remove the side panel that the cord has broken.It may be worth checking the other cord and replacing both if worn.Also check if something is catching to cause the cord to break.

Hope this helped.

Posted on May 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The machine won't turn on (no power light even). Trying to find the reset button. Where the cord enters the machine on the back ( top left) there is a a plastic cover housing the cord. I cannot see


Sounds like you have a bad door switch. Check to make sure there isn't a broken switch in the door housing. If not, this unit has a belt switch on it. Try spinning the drum by hand. If it's really loose and not tight, you need a new belt or the machine wont start.

Nov 25, 2013 | Dryers

1 Answer

Kitchen aide dish washer the door is sagging on one side. The hinge seems to be disconnected


If that is an under cabinet model, you need to pull it out of the position that it is in. The hinge pin is most likely damaged or broken. To pull it out, rermove the screws that are holding it to the counter top. Then slide it out

Dec 07, 2012 | Dishwashers

1 Answer

My hotpoint ultima wt761 door catch has broken how can i open the door


If you have a broken door catch you can get the door open by feeding some garden wire around the right hand outside of the door (between the door and the metal casing of the washing machine).

Once you've fed it in round the top right and bottom right curved corners pull the two ends of the wire to the left, so that the wire pulls against the lock mechanism, and the catch should release.

Feb 26, 2011 | Washing Machines

1 Answer

How install a drive belt on GE Dryer DBVH512EFWW.


Instructions Things You'll Need:
  • Phillips screwdriver
  1. Unplug the dryer and open the dryer door.

  2. Unscrew the screws under the top lip, where the dryer's door closes, with your screwdriver. Once these screws are removed, lift the top off of the dryer. On older models, the entire top will hinge upward out of the way, and on models made after 1997, half the top will pull off.

  3. Remove the screws on the inside-top corners of the front panel so the front panel of the dryer can be removed and set aside. On models made before 1997, the front panel should be carefully set to the right side; on newer models, the panel should be set to the left side of the machine. Be careful not to damage the door-control wires.

  4. Locate two screws approximately 6 inches off the floor on each side and remove them, allowing you to push the sides of the dryer slightly apart so the drum can be removed. Pull the drum slightly toward you and reach around to remove the dryer belt from the motor pulley. If the belt is broken, this step should not be necessary. Once the belt has been removed from the motor pulley, the drum should pull up slightly and out of the dryer toward you.

  5. Remove the old dryer belt and put the new one in place, with the ribs of the belt facing the drum. The slack part of the belt should be placed near the motor. Reverse the previous directions to replace the drum, replace the screws that hold the sides in place, replace the front and replace the top.

  6. Pull the dryer out from the wall and remove the four screws holding in the panel near the bottom of the back of the dryer. You will see the motor, the drum and the belt you just set in place. Loop the belt around the motor pulley and the idler pulley, and turn the drum by hand to make sure that the belt is straight and will stay in place. Screw the panel back on and push the dryer back into place against the wall.

Sep 22, 2010 | GE Dryers

2 Answers

Does the front panel come off?


If this is a Whirlpool Duet such as the one you posted this question under, yes, the front panel does come off. It can be a bit tedious, but these are steps required:

1. Unplug the washer.

2. Remove the washer top panel by removing the three torx-type screws (or 7mm) where it attaches in the rear of the washer. The panel should slide back, and then lift off.

3. Remove the operator console by removing the dispenser drawer and the scew(s) behind it. Take a putty knife and insert it under the console seam right above the door. If you push in slightly while pulling outwards the panel pops off. Use care not to pull or damage any of the wiring. You can leave the wires attached and simply lay the console across the top of the washer out of the way.

4. Locate the wire hoop retainer around the rubber door boot. It is located behind the rubber seam where it attaches to the door frame. Follow this hoop around to the bottom of the door opening and locate the wire tension spring. Gently pry this spring apart and pull the wire hoop from the groove. Pull the rubber boot from the frame and push it inside towards the wash tub. You will also have to remove the door boot from the fill tube on the left hand side of the door opening. There may be a small wire clamp holding it in place.

5. Remove the three screws that hold the door latch assembly in place. This is on the right hand side of the door opening. You can leave the latch in place as long as you remove the screws and push it inside slightly to remove it from the front casing of the washer.

6. Remove the door by removing the screws holding the hinges in place. Use care to support the door hinges when loosening. They can bend. Set the door aside in a location where it will not get stepped on or broken.

7. Remove the lower kick panel under the door. There are 3 screws under the bottom edge holding it in place. You may have to prop up the front feet of the washer for better access (a 2x4 works well for this). With the screws removed, the panel will drop down and come off. Sometimes the panel can stick. A slight tap on either side will knock it free.

8. Remove the front washer casing by removing the four remaining screws that are holding it in place. There should be two at the top and two at the bottom. Set the front casing aside.

Is there a reason why you need to remove the front panel? If you need further assistance, please let me know. I hope this help you.

Feb 14, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

The hinge of the washing machine has broken - Creda W100FW


The door hinge block has fallen inside the front of the washer.To retieve it, tilt the washer back, and you should find it at the left hand side.
Remove all screws securing 2 parts of door together, prise apart with a screwdriver or similar, and the door will come apart.
You can now access the hinge and all other partsd inside the door.
Trust this helps.
Thankyou.

Nov 28, 2009 | Creda W100FW Front Load Washer

2 Answers

The door to my Sharp microwave over the counter will not close


You can fix this. The same thing happened to my Sharp Microwave.

I got my parts at www.repairclinic.com . On my partidular model (which is probably onder than yours) there is a right hand latch and a left hand latch. Make sure of the one you need. Heck - buy them both.

The door was a little trickey for me to get apart - there was a plastic strip hiding the screws.

While I had it apart, I replaced the door safety interlock switches too ... you may want to consider replacing yours as well.

Also, as long as you have it all apart, you might want to change the lamp as well.

If you need more help with this ... tack a note on to this post.

I hope I have helped you ...

Thanks for visiting fixya.com

a

Oct 25, 2009 | Microwave Ovens

2 Answers

GE Side by Side Frig Door Flies Open to Far


Look under the front of the fridge, should be some adjustments to raise and lower the wheels or feet for leveling. Level it with a level on the top, should help keep the doors from swinging.

Sep 13, 2009 | KitchenAid KSCS25FKSS Side by Side...

1 Answer

Spring on door is broke. do I need to pull


The door springs are located at each door hinge and connect to the frame body along each side of the dishwasher. If you remove the lower toe panel directly below the door you should be able to see them. However, in order to access them to repair/replace you WILL need to pull the dishwasher out to get to them in most cases. You may not have to remove the dishwasher all they way, however, if you have enough slack in the water supply line, power cord and drain line. Just follow these steps:

1. Turn off the main power or unplug dishwasher.
2. Remove lower toe panel.
3. Remove the screws under the counter top holding the dishwasher in place.
4. With the screws removed, carefully pull the dishwasher out. Watch through the toe panel opening to see if you have enough slack in the power cord and water lines.

You may have enough clearance to locate the springs on the each side to make your repairs. If not, you will need to turn off the water supply and disconnect the water supply line on the left hand side inside toe panel. You may also have to remove the electrical lines inside the junction box inside the toe panel. It is usually located right in front for easy access. Make sure the power is turned off at the breaker, or the unit is unlugged before servicing the electrical supply. For reinstallation, the color codes are as follows:

BLACK - HOT (120 VAC)
WHITE - NEUTRAL (0 VAC)
GREEN (or Bare) - GROUND

If you have any questions, or need additional assistance, please let me know. I hope this helps you.

Aug 29, 2009 | Whirlpool 24 in. DU1100XTP Built-in...

1 Answer

Dryer Drum belt replacement


first unplug unit..remove front panel 2 screws..under the bottom side of timer console there is 2 pin or scews on each side pull down firmly,or if screws untighen slowly...just let console hang..now you can see the 2 screws holding bottom of front panel door.remove theses 2 screws..now step up on stool remove the 3 screws across the front top of unit,,theses screws are facing the ceiling..now remove door switch connection.remove front ,,you about there if belt has pop remove,if you have to replace a damaged belt..take your right hand and go though machine unit you fell the idler wheel on right side back pull down and take belt of idler wheel and motor pully at the same time ,,if you cant get ittake you left hand and help from the left side..to put back just reverse,,always unplug..

Nov 04, 2008 | Whirlpool LTE5243D Top Load Stacked...

Not finding what you are looking for?
Baumatic 23 in. BDW9 Built-in Dishwasher Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baumatic Dishwashers Experts

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Kolbrun...

Level 3 Expert

1205 Answers

Are you a Baumatic Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...