Question about InFocus Office Equipment & Supplies

3 Answers

Led light blinks red and shuts down after initial power up

Posted by on

  • jonesey1438 May 15, 2010

    Infocus LP 530 DLP. Lamp is new, i just installed it. lamp hour meter says 3, so i'm pretty sure i was successful in resetting lamp life meter. I have about 20 seconds at initial start up to scroll through menus, it then powers down, led light going from solid green to blinking red.Fan remains on while blinking red led light goes off.

  • jonesey1438 May 17, 2010

    Own a 3+ year old Infocus LP 530 DLP picked up at a garage sale. Lamp was blown so I purchased a new lamp, installed it, power on, LED light green, screen with menus come up, then 20 seconds later unit powers off, LED light flashes red (blinks). Fan still running though. I think I successfully reset the lamp hour meter as it reads 3 hours. Need advice on why unit is powering off, shutting lamp down in the process.

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • InFocus Master
  • 76,848 Answers

The projector bulb timer has expired. press the left arrow, right arrow and power switch simultaneously for a few seconds. The projector should power up, but this blinking light indiocates the bulb is at the end of its useful life span and a new bulb should be fitted as soon as possible, as there is a risk of the old bulb exploding

Posted on May 17, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,472 Answers

First off what is the make and model of the unit? Also how long have you owned it and how long have you had this problem? Once I have more information I can assist you further.
Thank you,
Lee

Posted on May 15, 2010

  • jonesey1438 May 16, 2010

    Its an Infocus LP530 DLP, I recently picked it up at a garage sale, with blown lamp. I purchased a new lamp, it seats and fits just fine. It powers up for about 20 seconds, LED light green, then shuts off (fan still on though) and LED blinks red. Its probably 2 or 3 year old unit, though not sure.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 229 Answers

I think the bulb is gone in the projector. Do you hear the fan go on? What is the age of the projector?

Posted on May 15, 2010

  • jonesey1438 May 15, 2010

    lamp is new, i just installed it. lamp hour meter says 3, so i'm pretty sure i was successful in resetting lamp life meter. I have about 20 seconds at initial start up to scroll through menus, it then powers down, led light going from solid green to blinking red

  • jonesey1438 May 15, 2010

    its an infocus lp 530 dlp projector. New lamp i ordered online fit and seated just fine into harness area.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do not my printer initialize & red light glow


LP-365W On Line LED Is Solid Red - samsung product ...

support-us.samsung.com/.../pop_troubleshooting_fr...

Samsung ElectronicsImportant: Before you perform any type of service on your printer that requires you to... Any of these conditions can cause the On Line LED to glow solid red:.

On Line LED Is Solid Red

support-us.samsung.com/.../pop_troubleshooting_fr...

Samsung ElectronicsDec 2, 2014 - Important: Before you perform any type of service on your printer that ...Any of these conditions can cause the On Line LED to glow solid red:.

Samsung ML-3561N Laser Printer Initialize - Questions - Fixya

www.fixya.com > ... > Samsung > ML > Samsung ML-3561N Laser Printer
ML-2570 Samsung printer having problem orange LED is blinking ... initializing stage green LED glows continuosly,After initializing Printer green LED turn into ... the red light remains on when i switch on the printer.. and it doesnt initialize the ...

Samsung glow plug Printers & Copiers Questions ... - Fixya

www.fixya.com > Forum > Tags > glow plug > Printers & Copiers
Printer Problems...red status light glowing I bought a Samsung CLP-310W a ...Samsung printer having problem orange LED is blinking in initializing stage ...

Reset for Samsung ML-1660 ' FixYourOwnPrinter


Dec 19, 2015 | Samsung ML 1610 Laser Printer

1 Answer

When i turn on my tv it tries to boot, blue mitsubishi home screen come up, i hear fan then it all shuts off while green light blinks.


Try a reset. Start by unplugging for 1 minute, then plug back in & if still won't restart try the following. If none of the following work, you will need a technician.

Initializing the TV in many cases can remedy a problem.
In the 2006 product line Initialization is now a user function.
Pressing the front panel "INPUT' and "FORMAT"
buttons at the same time activates Initialization. When
complete all user settings will have to be set again. The
table in Figure 4-3 list the User Initialization procedures.
Note: Pressing INPUT and FORMAT is the same as
the Initialization in the Option Menu (MENU-2-4-7-0)
Order Name Procedure Results Notes
1 System Reset Press <System Reset>
on Front Panel
Hardware & TV operating
software reset.
POWER/Timer LED flashes for 60
seconds. No customer settings
are changed.
2 User Initialization
Press <INPUT> &
<FORMAT> on Front
Panel at the same time.
All customer Audio &
Video settings are reset to
factory default.
All customer settings will need to
re-configured.
3 Reset System
Defaults
From the remote, press
<MENU> <1-2-3>
<ENTER>
All customer settings
except V-Chip are reset to
factory default.
Netcommand, Channel Memory,
etc., will need to be re-configured.
SERVICER
PROCEDURE 4 Initialization
From the remote, press
<MENU> <2-4-7-0>*
select "INITIAL" press
<ENTER>
All customer settings are
reset to factory default.
All customer settings will need to
re-configured.
MITSUBISHI RESET / INITIALIZATION CHART
CUSTOMER
PROCEDURES
Figure 4-3
Figure 4-4
LED Indications
The front panel LEDs, refer to Figure 4-4, also assist in
determining the cause of a symptom. Figure 4-5 illustrates
normal LED operation. Figure 4-6 shows the
LEDs response when a problem is detected and indicates
the possible cause.
Power/Timer
Indicator
Status
Indicator
Lamp
Indicator Condition
Off Off Off Off (standby)
Blinking green
fast Off Off Initialization (10 - 65 seconds)
Off Off Blinking
green fast Lamp runs for 1 min after PTV off
Green Off Off Power On
Blinking green Off Off Power On Timer is set
NORMAL LED INDICATIONS
Power LED Status LED Lamp LED Condition
High Temperature - check ventilation air flow.
(Temperature sensor is disconnected.)
Off Off Blinking yellow Lamp cover is open.
Lamp failure (Lamp fails to turn on)
Off Off Red (Lamp turns off after lighting)
Lamp is broken
Off Blinking Red Off Fan Stop
Off Red. Off Circuit failure. (Run Error Code Check)

Apr 08, 2015 | Mitsubishi WD-65731 65-Inch 1080p DLP HDTV

1 Answer

My Viera TV: TH-P42ST30z seems to have shut down. When I turn it on the pilot light initially flashes green then starts a sequence of 7 red flashes, a gap, 7 more red flashes and this continues indefi


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.

Oct 09, 2014 | Panasonic Televison & Video

2 Answers

Epson R230 with green led and red led blinking


This is general error of the printer. When you have to change the new mother board you should be initialized it then it can be ready mode. When you try to initialization you need printer printer adjustment program. You can batter find out from google & write down EPSON Stylus R230 Printer Adjustment program or ink reseat program.

Jun 12, 2013 | Epson STYLUS R230 InkJet Photo Printer

1 Answer

Picture went out and no audio, red light on power blinks seven times and repeats.


Physically disconnect the SU board and the SD board. (See precaution # 5)

Plug in the TV and turn it on.

Does the TV shut down and the power LED

blink 7 times?

Yes

No

Replace the Panel and the SU board.

(See precaution #3)

Reconnect the SD board only.

(See precaution # 5)

Plug in the TV and turn it on.

Yes

No

With the SU board and the SD board still disconnected, remove connectors SC2 and SC20 from the SC board (See precaution # 6)

Plug in the TV and turn it on.

Disconnect the SD board and reconnect the SU board. (See precaution # 5)

Plug in the TV and turn it on.

Yes

No

Replace the Panel, SD, and SU board.

(See precaution #3)

Replace the Panel and the SD board.

(See precaution #3)

Replace the SC board.

(See precaution #3)

No

Replace the D board.

(See precaution #3)

Does the TV shut down and the power LED

blink 7 times?

Does the TV shut down and the power LED
blink 7 times?

Feb 15, 2011 | Panasonic TH-42PZ700U 42 in. Plasma...

1 Answer

Jvc- 36f702. Powers up then shuts down right away and the red led blinks on the front panel?


Jvc- 36f702. Powers up then shuts down right away and the red led blinks on the front panel?

Dec 03, 2009 | JVC AV-36F702 36" TV

1 Answer

Blue led power light blinks even after shutdown


What operating system are you using? When the power led continues to slowly blink, that means that the laptop is in standby mode and not fully shut down. In Vista, if you hit the power button on the laptop or the power button under the start button, it is configured to go to standby and not shut down. Make sure to hit the arrow all the way to the right and select shutdown from the list of dropdown options.

Aug 28, 2009 | Gateway Computers & Internet

1 Answer

PS3 won't power up.


Hi,
THis issue is a motherboard issue, sort of like the 3 red lights on the Xbox 360.  It will need to be repaired.  If it is under warranty then send it to Sony, otherwise we fix this issue in my repair shop, just go to joegoods.com

Apr 02, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

The samsung monitor ssc21web shows system initialize... the three periods blink


ssc21 web does not work, It was a cameras shut down it says LA and AL why

May 15, 2008 | Samsung 4 Channel Dvr

2 Answers

Will not stay on


RED light is protect circuit = do not disable !
Look for C702 near flyback transformer - might be hidden in
glue = check it = if shorted, replace 102K / 2KV with 3KV =
Sony part # 1-161-754-00 and replace E994 pico fuse.....T.

Nov 08, 2007 | Hitachi 60UX54B/55K 60" Rear Projection...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2237 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you an InFocus Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...