Question about Dishwashers

Open Question

Bosch dishwasher cycle won't complete - picture of faucet in display

Bosch dishwasher constantly beeping during cycle and showing a picture of a faucet in the display

Posted by on

  • yuko13 Mar 24, 2009

    Dishwasher won't start and keeps beeping with a faucet in the display.
    It's a Bosch SHX55M05UC


×

4 Suggested Answers

  • 1 Answer

SOURCE: Bosch Dishwasher beeps during cycle

yes this does work , press the button marked 45 degrees and then switch on, . Thank god this works! should a stupid design and nothing in the instructions

Posted on Aug 16, 2009

  • 1 Answer

SOURCE: machine is beeping and a faucet is appearing in the panel

I just fixed this fault on my SHE68m05uc. The fault lets the machine run through any cycle and every ting else was working properly. In line between the fill valve and fill float assembly there is an electro magnetic impeller which is "open" if there is no water flow. the signal goes to the timer control board on the lower right side of the machine. If you Pull the impeller, take an OHM reading across the sensor that is mounted to the side of the impeller and blow into one end. If the measurement changes as it rotates, its good. if its shorted "0 Ohms" its broke. The part was about 17$

Posted on Aug 08, 2010

Macmarkus
  • 2605 Answers

SOURCE: How do you disable the cycle completion

Hello,

Welcome to FixYa.

I think can answer your question..."How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?"


Follow these steps...

**How to Operate the Cycle Completion Signal**


1. Open door, hold down program button (see
Beeper Table below) and simultaneously turn the unit "ON".


MODEL Program BUTTON

SHU 9950 Delay Start Hours
**SHU 9910-9920 Delicate/Econo** should be yours
SHU 8800/8810 Quick Wash

SHV 6800 Delay Start Hours
SHV 4800 Delicate/Econo
SHV 4300 Delicate/Econo


2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of "0", "1" or
"2". You are in program mode.

• If the display blinks with a "0", you will hear
no signal (indicates OFF).

• If the display blinks with a "1", you will hear a
LOW volume signal.

• If the display blinks with a "2", you will hear a
HIGHER volume signal.

b. For all other models with the beeper
function:

• If the machine beeps, then the Cycle
Completion Signal has been enabled.

• When you push the button again and it does
not beep, it means that the Cycle Completion
Signal has been disabled.

3. To change the program, press the program
button until the desired setting is selected.

4. Turn the Dishwasher off to take it out of
program mode.

* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.

Hope this answers your question and provides you with what you needed.

Thank you for choosing FixYa and good luck.

Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.

Regards,

Macmarkus :)

Posted on Oct 07, 2010

  • 77 Answers

SOURCE: My Bosch dishwasher makes a

The dishwasher sound can be disabled. You can go to the link to see how to disable the sound.

Bosch Dishwasher Signal


Good luck

http://www.appliancerepairlesson.com

Posted on Mar 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?


Hello,

Welcome to FixYa.

I think can answer your question..."How do you disable the cycle completion signal/beep on the Bosch SHU9915UC dishwasher?"


Follow these steps...

**How to Operate the Cycle Completion Signal**


1. Open door, hold down program button (see
Beeper Table below) and simultaneously turn the unit "ON".


MODEL Program BUTTON

SHU 9950 Delay Start Hours
**SHU 9910-9920 Delicate/Econo** should be yours
SHU 8800/8810 Quick Wash

SHV 6800 Delay Start Hours
SHV 4800 Delicate/Econo
SHV 4300 Delicate/Econo


2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of "0", "1" or
"2". You are in program mode.

• If the display blinks with a "0", you will hear
no signal (indicates OFF).

• If the display blinks with a "1", you will hear a
LOW volume signal.

• If the display blinks with a "2", you will hear a
HIGHER volume signal.

b. For all other models with the beeper
function:

• If the machine beeps, then the Cycle
Completion Signal has been enabled.

• When you push the button again and it does
not beep, it means that the Cycle Completion
Signal has been disabled.

3. To change the program, press the program
button until the desired setting is selected.

4. Turn the Dishwasher off to take it out of
program mode.

* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.

Hope this answers your question and provides you with what you needed.

Thank you for choosing FixYa and good luck.

Please take a moment to rate the solution provided and a short testimony if you feel it's warranted, but also let me know if you require further assistance.

Regards,

Macmarkus :)

Oct 07, 2010 | Bosch SHU9915UC Dishwasher

1 Answer

Water won't drain


Do the diagnostic test:
SHU 53 MODELS

To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show “88′ when REGULAR WASH button is pressed and “8h” when Delay Start button is pressed.
To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor (“Sensotronic”) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), display will show fault code “4′ and unit will continually fill and drain where testing won’t be completed. If flow switch (e5) has failed (opened), display will show “0′, water won’t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code “8′ immediately and testing will end shortly after water has started circulating.
---------
The dishwasher not draining is most probably faulty drain pump or drain hose is got bit loose.It has to be checked and confirmed
.You can get required parts from www.repairclinic.com
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Aug 27, 2010 | Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

After the wash cycle dishwasher beeps


Hello, welcome to FixYa. While I don't have access to my PC files at the moment as I am on my iphone, I believe this is the procedure for most B/S/H/ built dishwashers ( that means Bosch, Thermador, Siemens and Gaggenau ). To Enable or Disable the Cycle Completion Signal... 1. Open the door, hold down the ?Quick Wash? button and simultaneously turn the Dishwasher on. The ?Quick Wash? light will blink (program mode). 2. While the light is still blinking, push the ?Quick Wash? button. ? If the machine beeps, then the Cycle Completion Signal has been enabled. ? When you push the button again and it doesn?t beep, it means that the Cycle Completion Signal has been disabled. 3. Turn the Dishwasher off to take it out of program mode. I hope this answer's your question. Thank you for choosing "fixya". Please rate the solution favorably if indeed it was helpful, if not please let me know. Good luck. macmarkus :)

Jul 13, 2010 | Bosch 24 in. SHV4303 Built-in Dishwasher

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

1 Answer

Bosch SHU 6800 Water hot at sink only luke warm at the washer


BAD CONTROL BOARD TO TEST TO SEE IF THIS IS THE ISSUE RUN TEST PROGRAM
To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by
pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ “20” = version 0 without jumper). When
wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and
REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display
alone). Cycle Countdown display will show "88" when REGULAR WASH button is pressed and "8h" when Delay Start
button is pressed.
To start testing, press both SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended,
Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added
together, (e.g./ “6” = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil,
measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays
at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), display will show fault code "4" and unit will continually fill and drain where
testing won't be completed. If flow switch (e5) has failed (opened), display will show "0", water won't heat (to 150ºF) and
water won’t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code "8" immediately and
testing will end shortly after water has started circulating

Jul 18, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Machine is beeping and a faucet is appearing in the panel


I just fixed this fault on my SHE68m05uc. The fault lets the machine run through any cycle and every ting else was working properly. In line between the fill valve and fill float assembly there is an electro magnetic impeller which is "open" if there is no water flow. the signal goes to the timer control board on the lower right side of the machine. If you Pull the impeller, take an OHM reading across the sensor that is mounted to the side of the impeller and blow into one end. If the measurement changes as it rotates, its good. if its shorted "0 Ohms" its broke. The part was about 17$

Nov 20, 2008 | Bosch Evolution 800 SHE68M05UC Stainless...

2 Answers

Our bosch diswasher on auto wash will stop functioning in middle of the cycle start beeping and there is an icon of a faucet on the display. What does this mean?


Hello zeviemail
Welcome

You said, your Bosch dishwasher on auto wash will stop functioning in middle of the cycle start beeping and there is an icon of a faucet on the display.


What is your model number and the year of the dishwasher?

Oct 04, 2008 | Bosch Dishwashers

3 Answers

Bosch


f is fill fault to much or not enough water or water in the sump white plastic base the f code will not go away until you solve the problem when the f code shows up the drain motor will run all of the time

Apr 01, 2006 | Bosch 24 in. SHU6802UC / SHU6806UC...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

442 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

68038 Answers

Brad Brown

Level 3 Expert

14755 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...