Question about Sharp 55R WP5H 55" Rear Projection Television

1 Answer

I can't ajust my convergence . It looks like I'm watching 3D. What part do i need. I don't have parts manuel

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Sharp Master
  • 3,459 Answers

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

I can't ajust my convergence - 42d3683.jpg

7859b01.jpg

I can't ajust my convergence - e87380c.jpgttp://i.fixya.net/uploads/images/e87380c.jpg" alt="e87380c.jpg" class="h_mi" />
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. SeeI can't ajust my convergence - 69189a5.pnga fix

69189a5.pngCONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Posted on Aug 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv plays but picture is orange redish like tried to ajust color and tint still the same


Tv have a problems known as a picture convergence problems,it is dead.If the tv have any colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?Yes,then the tv convergence board it is dead,the tv convergence board must have replaced like 2 STK convergence ICS and some or all of resistors replaced too.To fixed the tv convergence board to solved tv convergence pictures problems.The tvs Shops will cost u like $300-350 for parts and lobors.

Jul 27, 2011 | Samsung PCL542R 54" Rear Projection...

1 Answer

My Hitachi 57F59A projection tv has a yellow color to it. I have ajusted the color and tried to reset and start over but still yellow. What could b wrong?


All projection TV sets have two very common problems. One is convergence ( 3D/Warped video or dead set) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. In some cases the TV will also not show any video. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....


  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.


7859b01.jpg

e87380c.jpg

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.

578ba6c.jpg
TV set after fluid change

65af323.jpg

69189a5.pngSOLUTION

You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here

May 04, 2011 | Hitachi 57F500 57" Rear Projection...

1 Answer

Hooked up PS3 to system and when watching DVD's the right side of the picture is blurry and appears doubled, like an old 3D movie without the red and blue glasses. When watching TV everything looks fine.


All projection TV sets have two very common problems. One is convergence ( 3D/Warped video or dead set) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. In some cases the TV will also not show any video. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....


  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.


7859b01.jpg

e87380c.jpg

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.

578ba6c.jpg
TV set after fluid change

65af323.jpg

69189a5.pngSOLUTION

You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here

Jan 20, 2011 | Mitsubishi WS-65809 65" Rear Projection...

1 Answer

The tv looks as though Im watching 3D. Tried unplugging for 5mins. Tried resetting picture settings nothing worked. Help please...


Very commom problems on the DLP tvs.The tv have a problems known as a convergence problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergence board have dead 2 STK convergence ICS and some or all of it resistors too.These parts must be replaaced on the tv convergence board to solved the tv convergence picture problems.The shop,will cost u like $300- 350 for parts and labors.

Jan 11, 2011 | Hitachi 53UWX10B 53" Rear Projection...

1 Answer

Picture looks like 3d i have ajusted screen but keeps going back to 3d and picture is bowed


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
•Screen looks 3D
•Colors don't line up
•One or more colors can't be adjusted when using the convergence menu.
•Screen is bowed or warped.
•TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems


a56fe79.jpg

6d0da0b.jpg

fcabb43.pngCONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya - CLICK HERE

Aug 25, 2010 | RCA P56923BL 56" Rear Projection...

1 Answer

Tv looks like 3d red color on screen


Sounds like the convergence circuit failed. Get an estimate from a repair shop. Not for DIY'ers.

Apr 23, 2010 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

I can't ajust my convergence . it looks like i'm watching 3D. what part do i need. I don't have parts manuel


STK ICs they are big black ICs Mats has them 1-800-628-1118 they will have part number on them example STK392-110

Mar 22, 2010 | Sharp 55R WP5H 55" Rear Projection...

1 Answer

My apex gb5108 convergence lines wont line up.I'm watching 3d


possibly the convergance ics have failed or convergance module
soldercon or both not a very costly repair

Aug 25, 2009 | Apex Digital GB5108 51" Rear Projection...

1 Answer

Picture is all distorted ,colors dont match up need 3d glasses to watch


HI, this is basic convergence failure. the convergence board controls the RGB stream and , if its malfunctioning or, the convergence chip set is damaged, it will distort the entire display and the colors will not be regulated correctly as you are experiencing at this time.

simply replacing the convergence board in this unit will fix your issue.

May 18, 2009 | RCA Televison & Video

Not finding what you are looking for?
Sharp 55R WP5H 55" Rear Projection Television Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73619 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Cindy Wells

Level 3 Expert

5054 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...