Question about Zassenhaus 175 Manual Grinder

2 Answers

Zassenhaus Turkish Grinder - handle

We lost the handle to our Zassenhaus Turkish Grinder.  Is a replacement available for sale?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Http://www.gittigidiyor.com/main/search.php?aramakategori=&aramakelime=kahve+de%F0irmeni&submitit.x=0&submitit.y=0&submitit=ARAMA&search_type=detail

Posted on Mar 22, 2009

Nothing anymore

Posted on Apr 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whatever the setting is at the grind is always fine. What can I do to re-calibrate the grinder?


Grind Adjustment Tools required: Large blade and medium Phillips head screwdrivers In order to adjust the grind, follow these steps (Refer to figure A): 1. Remove all coffee from the hopper. 2. Set selector knob to the finest setting (Espresso or Turkish) depending on the model. 3. Loosen both knob retainer screws in selector knob one turn only. 4. While pressing the bag switch, located behind the spout, press the START button so that the grinder will run during adjustment. 810 model - Press the ON or START button so that the grinder will run during adjustment. 5. With the grinder still running, turn the adjusting screw in the center of the selector knob slowly to the right until a slight clicking noise is heard. Immediately turn the adjusting screw to the left one grind setting. This is the finest grind obtainable. 6. Tighten both of the knob retainer screws. Once the ESPRESSO grind has been set (Turkish for Model 835, 875, 890), the other grind settings will automatically set correctly. 7. Press the STOP or OFF button. IMPORTANT: Always be sure the grinding burrs are not touching while the machine is running on the ESPRESSO/TURKISH setting. Otherwise serious damage to the motor may result. dr_buckhead.png

Nov 19, 2010 | Grindmaster 810 T Electric Burr Grinder

1 Answer

Grinding adjustments does not stay, but loosens during grinding. What should I do?


use a small abount of your ladyfriwenjds nail varnish on the adjustment nut or screw to prevent vibration from lossening it.

Please rate my help++++Thanks for using FIXYA

May 28, 2010 | Zassenhaus Knee Mill Hand Crank 156 Manual...

1 Answer

Just bought a used one, seems like the espresso grind is pretty course, is there an adjustment I can make?


To adjust this grinder turn the adjustment nob to the finest setting (ESPRESSO or TURKISH) Locate 2 small set screws on the adjusting nob. Loosen these screws (do not remove them) about one full turn. Start the grinder and, with it running, VERY SLOWLY and GRADUALLY, turn the CENTER adjustment screw clockwise until you begin to hear the burrs begin to touch (whirring sound). Back off the center screw about 1/16 of a turn, shut of grinder and re-tighten the set screws. Then try the grind on DRIP or there about for brewed coffee.

May 21, 2010 | Grindmaster 495 Electric Grinder

1 Answer

With the dial turned to "Turkish" I still get a very course grind. How to adjust/fix?


On the adjusting knob there are 2 set screws (outside of the center) and an adjustment screw (the one in the middle). First make sure the LARGE screws on the side of the SELECTOR plate are tight. Start with the selector on Turkish, with the grinder OFF loosen the set screws about one full turn each. Leaving the selector on Turkish turn the grinder on and gradually VERY SLOWLY turn the center screw clockwise. Eventually you will hear the burrs inside touching. After they touch back of the center screw about 1/8 of a turn. Tighten the SET SCREWS tight as they may allow the grinder to go out of adjustment if not tight. Test the grind with very little coffee and throw those grounds out. Then grind and brew! If these grinders are adjusted too fine you may have problems with the grinds not falling and may back up.

Apr 26, 2010 | Grindmaster 810 Electric Burr Grinder

1 Answer

How to calibrate my Bunn grinder.


It would be easier to pick up the manual in the commercial section under products from bunn.com, rather than me explaining it.
You have to loosen the nut on the adjustment wheel, then pull out slightly and turn towards coarse a few numbers, then push back in and turn grinder on and slowly turn toward fine, until the burrs slightly touch, you will hear a little metal on metal, at that point turn the grinder off, back off about slightly, then pull out adjuster and turn it to Turkish and tighten screw.

Mar 13, 2010 | Bunn -o-Matic G3 (3 lb. Commercial Coffee...

1 Answer

I took apart my Pasquini K2 doserless grinder for a cleaning this morning and while putting it back together, the locking pin is sitting flat, as opposed to being spring loaded as before. I didn't notice a...


It does have a spring that you may have simply lost. It is called a Grinding Setting Pin #HGP120. If you do not replace the spring you will lose your grind setting each time. I can send you a replacement spring via USPS for $2.50 +$4.95 Postage

My experience is working over 10 years at Pasquini as a master technician running the home repair sales and service center.

I stock all Pasquini parts for any service of your Pasquini espresso machines and grinders. Contact us for any of your Pasquini sales and service needs.

Feb 19, 2010 | Pasquini K2 Doserless Coffee Grinder

1 Answer

Zassenhaus knee coffee mill grinds too coarsely


I have a Zass and sometimes have a problem with it self adjusting, but when I do need to adjust it, I find that I have give it a good tap on the top to make sure it adjusts. So, just turn the knob counter clockwise as far as it will go, then give it a good knock on the top and bottom and try again. My mill offers the full grinding range, from a fine powder to large chunks.

Feb 04, 2009 | Zassenhaus Knee Mill Hand Crank 156 Manual...

1 Answer

How do I descale a Thermos?


For excessive staining use of household stain or scale remover is recommended. To remove difficult stains fill your flask with hot water, add one teaspoon of bicarbonate of soda and secure cap. Soaking overnight produces excellent results. Always rinse before re-use.
this is from http://www.thermos.co.uk/care.php
my hubby used it as he uses his thermos daily... so goodluck!

May 05, 2008 | Zassenhaus Knee Mill Hand Crank 156 Manual...

1 Answer

My cofee maker!!!!!


May, The only Zassenhaus products I know of are burr grinders, not coffee makers. About any kind of coffee maker...are you speaking about the appliance attachment cord? If you have the brand, or can carry the unit in, the cord can be matched at the local hardware store. If you don't have such access, get the name/model number and call www.smallappliance.com.

Hope this helps.

Nov 25, 2007 | Zassenhaus Knee Mill Hand Crank 156 Manual...

Not finding what you are looking for?
Zassenhaus 175 Manual Grinder Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zassenhaus Coffee Grinders Experts

Tony R.
Tony R.

Level 2 Expert

24 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Ray Murphy

Level 2 Expert

67 Answers

Are you a Zassenhaus Coffee Grinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...