# Control lock I woke up one morning and the control lock was on. Is there a certain way to fix this? I cannot do laundry and it is piling up!!! Thanks.

Posted by on

• Anonymous Apr 01, 2008

yes, i have the same problem; i pressed the end of cycle several mins but not working. help me!

×

• Level 1:

An expert who has achieved level 1.

• Contributor

Try pressing and holding the "End of Cycle Signal" button at the bottom right corner of the control panel. This works for me!

Posted on Apr 01, 2008

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
Good luck!

Posted on Jan 02, 2017

×

my-video-file.mp4

×

## Related Questions:

### Brian Power Question? Five Associates stray off course during The Expedition and find themselves in a new Quest where there is nothing but a pile of molecules and the Avatar. Exhausted from playing all...

Every associate leaves 4/5(n-1) molecules of a pile of n molecule. This result in an awful formula for the complete process (because every time one molecule must be taken away to make the pile divisible by 5):

4/5(4/5(4/5(4/5(4/5(4/5(p-1)-1)-1)-1)-1)-1), where p is the number of molecule in the original pile, must be a whole number.

The trick is to make the number of molecule in the pile divisible by 5, by adding 4 molecules. This is possible because you can take away those 4 molecules again after taking away one fifth part of the pile: normally, 4/5(n-1) molecules are left of a pile of n molecules; now 4/5(n+4) =4/5(n-1) +4 molecules are left of a pile of n+4 molecules. And because of this, the number of molecule in the pile stays divisible by 5 during the whole process. So we are now looking for a p for which the following holds:

4/5×4/5×4/5×4/5×4/5×4/5× (p+4) = (46/56) × (p+4), where p is the number of molecule in the original pile, must be a whole number.

Therefore, the smallest (p+4) for which the above holds, is 56.

So there were p=5 power 6 - 4 = 15621 molecule in the original pile.

Dec 16, 2010 | Cell Phones

### I have a galaxy fridge, side by side. it woke me up this morning making the LOUDEST noise! it sounded like it was coming from the motor underneath? i don't know a thing about refrigerators.... i just know...

Good day,
Motors make noise. There a 2 in the bottom back of the machine.
One is the compressor itself and the second is the cooling fan motor located in the same area. Someone will have to remove the rear bottom cover. If it's the fan motor, then the repair cost is nominal. On the other hand, if it's coming from the compressor itself, you have a major problem.

May 21, 2010 | GALAXY Microsystems 25.4 cu. ft....

### Kenmore He2Plus Washer: Controls Locked button lites up & beeps

plug it back in and there should be a buttong somwhere toward the corner and in small lettering"un-lock/lock" hold that button for 5 secs and see if it un-locks the board. if it dont the your board might be bad....hopefully this helps

Jul 30, 2009 | Washing Machines

### Help, I am drowning in laundry!

check ot whether the motor is working.

or

check out the above link by clicking on it

or
http://www.applianceaid.com/washers.html

hope this helps...

thanks.

Oct 05, 2008 | Whirlpool Duet GHW9150P Front Load Washer

### F22 code appears on Kenmore Elite Front Load washing-?

communication error between control board and panel. Make sure both are replaced together. common problem

May 27, 2008 | Kenmore Elite 45986 Front Load Washer

### Bosch WFL 2462

Your exit hose behind the machine has to go over a certain height before it goes into your wall standpipe or sink. The height is marked behind your machine, approx 3 feet above ground level. The hose should put about 3 or 4 inches into the standpipe, & not fitted airtight.

Possible u didnt connect well after your pump job or ........

May 02, 2008 | Bosch Classixx WFL 2462 Front Load Washer

### Control button on

one of the buttons has a lock emblem underneath it try holding it down 3-5 sec this should release control functions

Apr 29, 2008 | Whirlpool Duet GHW9150P Front Load Washer

### Whirlpool duet

On the far right sode of the control panel there is a unlock control reset button. Hold it for 3 seconds and the fault will clear.

Mar 18, 2008 | Whirlpool Duet GHW9150P Front Load Washer

## Open Questions:

#### Related Topics:

63 people viewed this question

Level 3 Expert

Level 3 Expert