Question about Epson Stylus 2200 InkJet Photo Printer

1 Answer

Yelllow wont print,...changed cartage cleaned

Yelllow wont print,...changed cartage cleaned heads help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 108 Answers

If after cleaning the print head and changing the cartridge yellow still doesn't print, it sounds like there may be a problem with the print head or the board that controls the print head. The print head may not be receiving the signal to turn on. Check the circuit boards on the machine for obvious damage or a burn smell. Depending on the model printer it may be cheaper to replace the printer than to have the board or print head replaced.

Posted on May 15, 2010

  • 2 more comments 
  • Haruspex Dec 17, 2010

    I let my 2200 sit for over two years, and now Yellow or Red doesn't print after numerous cleanings. I have to figure out how to manually clean the head, jets... I doubt that it is a circuit issue.

  • Ben
    Ben Dec 17, 2010

    Original post by jamesgresik stated that "cleaned heads" , that is why mentioned a circuit board issue. Of course if you let your printer sit for 2 years the jets are going to be clogged

  • Haruspex Dec 17, 2010

    It's the method of cleaning that I am referring to. I have found no information on how to reach the jets on the Head cartridge. Are the ink jets directly below the intake spindle of each ink reservoir? Does the whole head assembly come off. It moves up a little using the Paper/Envelope lever on the back of the Printer. I’m not finding a clear answer on this.

  • Ben
    Ben Dec 18, 2010

    I am sorry I miss understood your first comment. The "Jets" or the "Print Head" where the ink cartridges install was not engineered for easy removal. Most are on a shaft and are belt driven. Use extreme caution if you attempt to remove the print head. These printers are normally built so you toss them and buy a new one.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Full of ink not printing just blank pages dxmodel


you need to run a head cleaning on your printer. open control panel / printer's/fax's ..right click on your printer and go down to properties ..you will find head cleaning in there ( you might have to run it a few times )

Apr 23, 2015 | Epson Office Equipment & Supplies

1 Answer

Getting doubles/shadows


change the black ink cartage and try

Aug 07, 2014 | Kodak Office Equipment & Supplies

1 Answer

Printer works but only color is printing, the black is faded and only partially printing. I have tried 3 new print cartages and it still does not print right. No error message


The print heads for the black cartridge are probably plugged.

You can try using the software to clean the printheads. Go to the Kodak AIO Home Center and under "Maintenance" there will be a button that will allow you to clean the print heads. If you don't notice a difference after 2 or 3 cleanings you will have to remove the print heads (youtube video here: http://www.youtube.com/watch?v=n1AYgfPHy0o) and clean them with warm water and some Q tips.

Mar 06, 2011 | Kodak ESP5250 All-In-One InkJet Printer

1 Answer

Suddenly it wont priny black, have tried to replace with i new. Paper is offcourse removed, but it wont print black. Have run all cleaning programs. Could it be under the ink tank? How can i get to it?


Maybe you need new black ink cartage, or new color if its one pint cartage. follow the procedure under the bonet to change the ink cartages,. hope this helps

Nov 30, 2009 | Canon PIXMA iP8500 InkJet Photo Printer

1 Answer

My canon bjc 3000 inkjet printer is feeding paper but not printing. Does the head need cleaning? How is this done?


could be possible that its either dired up or out of ink, open its bonet and remove cartages, clean head with a soft cloth removing any dried ink give cartages a good shaken see if any ink comes to head, and try again. hope this helps

Nov 30, 2009 | Canon BJC 3000 InkJet Printer

1 Answer

When printing, the only thing that prints are lines in red or blue, the black wording does not show up, help


first clean the cartage 2 or 3 times, if it still doesn't print change the cartage. its out of ink or its hardend and wont flow ..

Jul 02, 2009 | Canon PIXMA MP830 All-In-One InkJet...

1 Answer

My Canon i860 just can't print out black words, it's frustrating


pull the ink cartage back out to see if a clear film is not on the cartage??? Check the area by cleaning the ink cartage with rubbing alchole, and also the area that the ink cartage goes into. Use a cotton ball the clean these area with.

Jan 31, 2009 | Canon i860 InkJet Photo Printer

1 Answer

Epson CX5500 does not see cartage replacements as being full ,so will not print !!


Ok 

If your printer cartages are full filled and will not able to print. Please follow the following steps-

1- Uninstall the printer driver and disconnect printer from PC.
2- Download the latest Epson Stylus CX5500 Driver 6.5b Windows 2000/XP  from given web link

    http://down3.driversdown.com/Printer/CX5500_W2K_65bE.zip

3- Install the printer driver from downloaded file and connect printer as setup ask.

4- Now remove the cartages from printer and clean the connecting points & inkjet point by soft cloath.

5- While cleaning the cartage's injet points you will must see the ink on cloath. If ink does not see on cloath may be your cartages are dry. try to clean them by little force.

6- connect the cartages to printer. tyr to print.

It will help you.

Nov 22, 2008 | Office Equipment & Supplies

1 Answer

Will not print blue


Try this I triedi in my printer cartridge which was stuck for a while and only prints in red other colors dont. First you remove the cartridges get a clean dry tissue / towel paper and smudge the cartridge printing heads to the tissue it should give all the colors if not the ones that dont may have hardened. Get warm water (Clean) in a bowel and submerge the printing heads on the water not the entire cartridge to dissolve any deposits then try them again. Hope it works it worked on mine.

May 30, 2008 | HP Officejet Pro L7580 All-In-One InkJet...

1 Answer

No yelllow on Pixma MP530


Yes you are correct, it will be print head, to ensure long life of head stay clear of so called compatible supplies they often trash heads.
953c462.jpg Part info/pricing

Jan 11, 2008 | Canon PIXMA MP530 All-In-One InkJet...

Not finding what you are looking for?
Epson Stylus 2200 InkJet Photo Printer Logo

443 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...