Question about Galileo 90mm Reflector Telescope with Multiple Ocular Holder

1 Answer

I cant see out the thing at all. should both ends be stay covered.?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,186 Answers

The end with the FOCUSER is point UP. The mirror is on the bottom. Many beginners mount these BACKWARDS pointed toward the ground.

Posted on May 16, 2010

  • Joe Lalumia aka TelescopeMan

    Take the cap off of the tube nearest the focuser end.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lofra oven doesent stay alight


I had the same problem with my Lofra, I removed the cover on the bottom of the inside of the oven and then unscrewed the metal bit under that. Then I tested it again so I could see why it wasn't lighting up. Turns out the heat sensor was in between two flames and wasn't detecting that the gas was on. I wiggled things around a bit until it stared working, then put the cover back on. Now it works wonderfully. Now I just have to fix the timer.. It doesn't ring when it reaches the end. Hope this solution works for you guys.

Dec 18, 2012 | Lofra MXD96MFEPI Dual Fuel (Electric and...

1 Answer

Alarm light stays on and there is no heat


On the back there's a round cover held on with 3 Philips screws. Remove it. You should see a peice of thermal/electrical insulation with a red wire going in one end and a white wire on the other end. It's screwed down with a wire hanger and covering a 15Amp FUSE. Its part number is "SF119U-1", made by SEFUSE, rated 15Amps/125degC. The sell for about $5 for 5 of them. You can get one at RadioShack or better yet, replace it with a thermal circuit breaker (part # R59-15A), which costs about $5, but the nice thing is that if/when it trips, you can reset it instead of replacing it.

Nov 06, 2012 | Optimus H-4436 Electric Heater

1 Answer

My kreepy keeps coiling at the deep end of pool and stays there what do i need to do so that it cleans the whole pool?


There are a couple of things that you can try to get your pool cleaner to cover both ends of the pool. First, use an eyeball diverter to make sure that your water flow is correct to make the pool cleaner function in the proper pattern. Your return lines could be pushing the cleaner only toward your deep end. Secondly, if your hose is connected to your filter at the deep end of the pool, it could be that your hose is not long enough to cover the entire pool. You might need to add hose lengths. You will also want to adjust your hose weights.

Jul 16, 2011 | Universal Kreepy Krauly In-Ground Pool...

1 Answer

I cant remove panel bcause i cant get door open now what?


there are three locations for fuse panels the one under the hood use a screw driver and push in on the locking tab as you lift on the cover the others are on either end of the dash the end covers remove to access these

Jan 22, 2011 | 2000 Acura TL

1 Answer

Cant get spark plugs out of my 1996 Mazda Protege, I have a 5/8 socket and and extension that is long enough, but for some reason it wont grab the spark plug, is there a special wrentch for this model. My...


your spark plug wires have a rubber boot on the end of them and some times they come off and stay on the spark plug to where you can't get the socket on the plug. If you have oil on your plug wires than you need to replace the valve covers. You can use a long thin screw driver to get the boots off the plugs. It may take some time but they will come off.

Oct 07, 2010 | 2001 Mazda Protege

1 Answer

Phone got wet, service is offline mode stays on


You can try a couple of things to try and save it. Phones do not like water. If you are mechanically inclined, take the phones rear cover and front covers off. Take the internal parts and put them on the dash of your car all afternoon. If you cant take apart try this or you can put the phone in the oven (no joke) at a real low setting for a while. You don't have much time to dry it out before it gets corroded so do this right away. If it doesn't work you can always trade it in for another phone.

www.usedcellphoneshop.com

May 08, 2010 | Samsung SPH-M300 Cellular Phone

1 Answer

I took the sprocket cover off to remove the bar and chain while i had the chain break engaged. (idiot) NOW i cant get the thing back on. any ideas?


It must be reset before you can reinstall it.
This answer stolen from Dolfoff;

Clamp the cover in a vise being careful to stay on flat surfaces of the cover (use wooden blocks if needed) and pull the brake lever back to the "OFF" position. It's a strong spring so pull hard in the direction that would be towards the rear of the saw if the cover were installed.
Hope this helps.


GL
Lou


Oct 06, 2009 | Husqvarna , No.455 Rancher, 20" Gas -...

2 Answers

Cant find part


There is a local KTM dealer here where I live. The number is 904-247-1622, I've been there and they seem to be really nice people and will work with you.

Jan 16, 2009 | 2008 KTM 300 EXC-E

1 Answer

Console fell and now front cover is broken and apart


no you cant fix it you have toget a new one

Dec 28, 2008 | Nintendo Wii Console

1 Answer

Cant play tape


the end-of-tape optical sensor is at fault. either it is very dirty, has failed or something else is detecting end of tape. many VCR's now will auto-eject the tape upon end of tape detect

Dec 28, 2006 | Proscan PSVR73 VHS VCR

Not finding what you are looking for?
Galileo 90mm Reflector Telescope with Multiple Ocular Holder Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Galileo Optics Experts

Joe Lalumia aka...
Joe Lalumia aka...

Level 3 Expert

3186 Answers

Brad Brown

Level 3 Expert

16166 Answers

NOEL
NOEL

Level 3 Expert

8023 Answers

Are you a Galileo Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...