Question about Navman PiN 570 GPS Receiver

1 Answer

Pin 570 wont boot after hard reset

This was working fine until it wouldn't switch off with the power button the side. so i pushed the soft reset button on the base of the unit but still no fix, so i moved the hard reset switch to the left then back to the right, now the display lights up with some text on the top

DOWNLOAD IMG

i presume it is waiting for some sort of operating system or boot image to be loaded into this navman pocket pc
even if the supplied navman MMC card with the maps is inserted then nothing happens.

if i plug the sync / charger usb cable into the pc, then a new device is found, but drivers or software cant be found for it on the supplied CD's or the microsoft site.
the new device comes up as

SEC S3c2410x Test B/D

i installed microsoft active sync off the supplied CD onto the pc, but it wont see the navman device connected to the usb port. the newly installed SmartST software cannot see it either.

I cant find any support on the navman web site for this problem.

any ideas?

Posted by on

  • 1 more comment 
  • fastdude
    fastdude Apr 01, 2008

    Ta, this put me on the right track!

    LEFT IT ON for about 2 hours TILL almost all POWER WENT AWAY FROM UNIT with the DOWNLOAD IMG message on the otherwise blank lighted up screen

    Then I moved the hard reset switch to the left then back to the right, the Navman logo showed and it booted and loaded the smart st from the MMC memory card. it warned me about a low battery, and said something about registering on the CD.

    i plugged it into the charger straight away
    i plugged the usb into the pc and it was recognised as a "windows powered pocket pc 2003"
    Microsoft active sync now sees it as well.

    everything seems to be ok now.
    strange how the restart didn't happen with a fully charged battery...

  • Cliff May 26, 2008

    I have a Navman PiN 570 GPS Receiver it doesnt respond to power on/off
    button it only powers up by moving Hard Reset Switch to right then
    freezes saying navman in top left corner and SmartST in bottom right
    corner, can anyone give any adivce on how i may solve this problem?
    thanks in advance

  • stelio_k May 11, 2010

    gfgdhjfgdhjhgfd

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 28 Answers

RECENTLY I DID PRETTY MUCH THE SAME THING
SO HERE IS WHAT I DID :
" I TURNED IT ON AND HIT THE HARD RESET AND THEN LEFT IT ON TILL ALL P[OWER WENT AWAY FROM UNIT
SECOND I HAD TO DOWNLOAN A NEW VERSION FOR MY UNIT ; MEANING MAP
THEN I TOOK THE BATTERY OUT AND AND PLUGED IN MY USB CORD AND IT TOOK IT
I PUT MY BATTERY IN AND CHARGED OVER NIGHT AND WELL IT SEEMS LIKE A LOT TO DO BUT FROM WHAT I UNDERSTAND MY DRIVER GOT BOOTED OFF THE UNIT AND ANOTHER DRIVER FOR A MODEL WAS ATTACHED
HOW I DONT KNOW BUT MY UNIT WORKS NOW FOR THE LAST 4 MONTHS NO PROBLEMS

HOPE THIS HELPS YOU OUT RICHARD FROM CHICAGO

Posted on Mar 31, 2008

  • richard del priore Apr 05, 2008

    hope al is fine now

    richard from chicago

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know how to reset my kids Click N Kids tablet?


Hard reset or soft reset? Softreset, push a pin into the reset hole on the back or side. Hard reset, hold down vol- and power until the reset screen appears.

Aug 03, 2015 | Tablets & eReaders

1 Answer

How do i do a hard reset on a magellen maestro 4040?


  • 1 Slide the Magellan GPS unit's powericon1.png switch to the off position, if your GPS has a two-way slide-style switch. Hold the switch in the off position for 8 seconds or more to reset the device.
  • 2 Slide the switch to the reset position if your GPS has a three-way switch. These switches feature "Reset," "Off" and "On" labels. Hold the switch on the reset position for 10 seconds to initiate a reset.
  • 3 Inspect your GPS for a reset pin hole if the unit has a push-down power button rather than a switch -- check the bottom and sides of the device for a pin-sized hole. Insert a pin or a straightened paperclip into the hole, pushing until you feel a slight pop. Hold the pin or clip down for 10 seconds and the GPS will reset.


  • Read more: http://www.ehow.com/how_5635240_reset-magellan-gps.html#ixzz33LpAdUJE

    Jun 01, 2014 | GPS

    1 Answer

    How do you reset a Magellan 1700 GPS?


    FAQ on your unit says this.

    Depending on the power switch your unit was designed with follow the instructions below:

    Slide Switch If your unit has a Slide power switch then slide and hold the power switch in the off position for more than 8 seconds.

    Push Down Power Button If your unit has a Push Down Power Button for a Reset pin hole on the bottom or on either side of the unit. Take a pin or an end of a paperclip and insert it into the hole and push in until you feel it pop slightly, hold it for 10 seconds. Your unit will reset itself.

    Reset Power Switch If your unit has a Reset Power Switch then it will have a three position power switch (Reset, Off, On), if this is the case slide the switch to the reset position and hold it for 10 seconds to perform the reset.

    If that doesn't work, contact them direct. sometimes they have to install clean firmware.


    MagellanGPS Technical Support Consumer Sales Customer Service

    Apr 08, 2017 | Magellan Roadmate 1700

    1 Answer

    Asko W6761 - seems fine, starts to fill 40 seconds then stops!


    Hello, my W6761 becomes the same. When it happens, you can clear the problem by "soft ware reset". Following is the procedure:
    1. Power it on
    2. Push Start/Stop buttom 5 times
    3. Push "Enter", ">", "<", "Menu" buttons (from right to left)
    4. Again, push "Enter", ">", "<", "Menu" buttons
    5. Wait for 30 seconds that the above soft ware cycle resets the internal status
    6. Power it off and on, again
    7. You need to execute above "soft ware reset" within 15 seconds

    Start washing and check to see if above reset the problem.
    If it does not begin to work, repeat above "soft ware reset" cycle until it begins to work.
    My W6761 once needed to repeat above cycle 7 times to solve the problem.
    This problem happens in mostly in warmer season, so this will be related with high ambient or water temperature.

    ASKO technician may replace the controller but even with the replaced controller, this problem often happens.

    Tsunett

    Mar 16, 2009 | Asko W6761 Front Load Washer

    1 Answer

    IQue 3600 Fatal Alert


    You'll have to do a hard reset. Push the reset button, then hold the power button until the Palm Power appear and then release the power button. Next it will ask if you want to erase the data. I hate to said this but select yes. No will not work. Then after the inital set up run a HotSync.

    Jun 18, 2008 | Garmin iQue 3600 GPS Receiver

    1 Answer

    NAVMAN PIN 570


    Try cold boot, that is factory reset button on the right of the power/usb cable slot.

    Feb 12, 2008 | Navman PiN 570 GPS Receiver

    1 Answer

    Pasword reset


    if you mean the phones password the only way is a hard reset, remove wait 10 seconds and replace the battery. If you mean the sim password/Pin contact your service provider (company who supply your sim)

    Hard reset
    press and hold the two soft keys (the two buttons with a "-" each side of the navigation keys) while breafly pressing the power switch then follow the instructions. If it boots up as normal, remove the battery and try again.

    NOTE this will remove all data and restore to the installed rom

    Feb 07, 2008 | HTC S710 Smartphone

    3 Answers

    Tomtom 710 broken


    What seems to be the nature of the problem?

    Feb 01, 2008 | Tomtom GO 700 GPS Receiver

    2 Answers

    Palm Tungsten E2


    TRYING PUSHING A PIN INTO THE LITTLE HOLE IN THE BACK THIS WILL DO A HARD RESET IT MIGHT HELP YOU. GOOD LUCK

    Jan 29, 2008 | Palm Tungsten E2 Handheld

    Not finding what you are looking for?
    Navman PiN 570 GPS Receiver Logo

    904 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Navman GPS Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    The Knight
    The Knight

    Level 3 Expert

    74459 Answers

    Neil Gossage

    Level 1 Expert

    4 Answers

    Are you a Navman GPS Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...