Question about Technics SA-DX1050 Receiver

1 Answer

Not working when i turn on my receiver technics sa-dx1050. its say (F 10)on the display.and then switch off.what can i do?to reset it.

Posted by on

  • Anonymous May 23, 2009

    call 717-232-9715 to order a part

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Operationg instructions says it is "F 70". When it appears it says to turn the unit off, disconnect the aC power supply cord, then reconnect and turn theunit on. Consult your dealer if "F-70" remains on the display.

Posted on Jul 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Digital input glitch, switches randomly from analog to digital.


what connections do you use for the device you are listening to, and what device are you listening to when this happens. you should use either an analog, or a digital connection to a device, but not both

Mar 08, 2013 | Technics SA-DX930 Receiver

1 Answer

Technics sa ex400 help reset light staying on


I to have a Technics SA-EX400 Receiver, The reset light stays lit also, I assumed it is normal. When I push it, it says operating normaly...

Jan 04, 2012 | Technics SA-EX400 Receiver

1 Answer

When I turn on my technics sa-gx amplifier I can't hear the sound


Have you noticed if the speakers selector switch in the front panel is set to off ? That position for the switch is only suited to listen heaphones. Good Luck.
Flavio/BRAZIL

Jul 28, 2010 | Technics SA-DX750 Receiver

2 Answers

My Technics AV Control Receiver SA AX530 is in overload


An amplifier should never be turn on without speakers, it will overload internally.
make sure speakers work and try again.

Dec 04, 2009 | Technics SA-AX530 Receiver

1 Answer

Technics SA-AX540 Receiver


It is unlikely that the display itself is faulty although it can happen. The typical problem is either the backlight is defective or the suply to the unit has a bad connection. If you can solder, try resoldering the pins on the display itself. The pins on the ends are the power and ground. I don't recall whether or not your model has a separate back light bulb or not. That too could be burned. Chack for that too.

Keep us posted,
Dan

Mar 02, 2009 | Technics SA-AX540 Receiver

1 Answer

SAAX7 Technics stereo receiver stops broadcasting after 20-30 min


Ron- The fan does not turn on when the receiver is first powered on, it will run when the amplifiers begin to run HOT, they are kinda controlled by a thermo switch, if the fan does not turn on usually the receiver will shut down and display a OVERLOAD message in the display panel. My advise is to keep the unit well ventailated with plenty of breathing space around the top vent closure, this will allow air flow when loud volume output is used. Also use the rated ohm speakers with the SA-AX7,

Jan 25, 2009 | Technics Audio Players & Recorders

1 Answer

Overload on Technics SA-AX710 Receiver


u can measure the speakers impedance, if is ok. I think this can be a problem, when is speakers with 4ohm conected.

Dec 21, 2008 | Audio Players & Recorders

2 Answers

Technics SA-DX950 has lost digital sound


This may sound like a silly check, but verify that the tape monitor switch is not engaged. What is the quality of the sound when turned up? Is the cound clear or raspy?

Thanks,
Dan

Dec 04, 2008 | Technics SA-DX950 Receiver

1 Answer

I hooked two Receivers up in series a Technics SA-DX930 and a different kind I'm not sure wut kind. They worked great for a while, but when they got turned up a little louder they both quit puting out...


you blew your power amp board, you cannot hook them in series due to impediance matching and improper input levels, cheaper to replace reciever than the board

Apr 30, 2007 | Technics SA-DX930 Receiver

Not finding what you are looking for?
Technics SA-DX1050 Receiver Logo

Related Topics:

534 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4861 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...