Question about Maytag MAH6700AWW Neptune Front-Load Washer

1 Answer

Model MAH4000, will not spin out, door lock will

Model MAH4000 will not spin out door lock will not work.

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

Check if the "locked"or "door locked" light comes on. If it does not, you need to replace the wax motor in the door lock assembly and the machine control board, which is inside the control panel. The control board is expensive, so instead of buying the whole control board, if you're good in electronic repair and soldering, try checking ebay for the control board repair kit. Search for "MAYTAG NEPTUNE WASHER R11 Q6 REPAIR KIT". It has all instructions how to do the repair. Good luck!

Posted on Aug 21, 2010

  • Shawnvega Apr 27, 2012

    What if it does lock, fill but won't do anything after that. Won't spin but will fill.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model MAH3000AWW won't spin


As giving info it seems it needs new control board and door lock .as I could see this is very old model and parts are very expensive

May 06, 2014 | Maytag Neptune Washer Door Mah3000aww

1 Answer

What is the value of R-11 in the maytag ,MAH4000 AWW it's in the door lock wax motor for the hinh speed spin


The R-11 is on the control board, not in the door lock or wax motor. Value is 3.9KOhm, plus you'll need to replace the Q6 triac if R-11 is burnt out, as it's also dead.

Jun 17, 2010 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Front loading Neptune will not spin.


if you have a model # mah2000 or mah3000 or mah4000 searies washer and the door lock light does not come on and will not spin. There is a good chance that your wax motor for you door lock has fryed you control board. you can inspect the control board that is located in the top consol and look for two resiter that are right next to eachother chard.

If you do find this, you will need to replace the control board and the wax motor for the door lock or it will just fry the control again.

Jan 12, 2010 | Dryers

1 Answer

MY MAYTAG NEPTUNE MAH4000 WILL NOT DRAIN OUT OR SPIN


Check if the "locked"or "door locked" light comes on. If it does not, you need to replace the wax motor in the door lock assembly and the machine control board, which is inside the control panel. The control board is expensive, so instead of buying the whole control board, if you're good in electronic repair and soldering, try checking ebay for the control board repair kit. Search for "MAYTAG NEPTUNE WASHER R11 Q6 REPAIR KIT". It has all instructions how to do the repair. Good luck!

Dec 10, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Neptune MAH4000 AQW belt will not stay on.


If you installed the belt correctly but it still comes off, that means most likely that the drum pulley is tilted, which indicates another problem - the central bearings are going out. Another symptom for that is a loud noise when the drum is spinning fast. The cure for that would be replacement of the outer tub or just replacement of the bearings with seal.
If there's no noise during high spin - check if the drum pulley or the motor is loose.

Good luck,
Vladimir
First Choice Appliance

Jun 19, 2009 | Maytag Neptune Washer

1 Answer

Sometimes there is water that fills in my washer after I use it. It does not happen right away but by the next day. I don't know the model but I do know this is an old washer....gold....I have had it for...


Q - My washer seems to keep filling  with water, the water keeps coming in the washer and going out the drain without the washermotor running.
A - This often is a drain hose that is too low or a drain hose that has been pushed too far down inside the stand pipe....the water is actually siphoning out of the washer. Do not "seal" the drain hose to the house plumbing pipe, this will also allow the water to be siphoned out.
  1. Boot change helps
  2. Consumer Display Code Table on the Electronic Display Maytag Neptune Front load washer
  3. Free on-line repair manual for the Neptune washer MAH3000, MAH4000, MAH5500, MAH7500  ( Acrobat reader required )
  4. How to access the console on the mechanical timer models
  5. How to access the workings of the washer
  6. My washer door is locked and it will not open up...HELP
  7. My washer will start when I push the start button, but a few seconds later, it will shut off
  8. My washer will not pump out + pump noise problems
  9. My washer will not spin
  10. Odor complaints from the front load Neptune washer - mildew complaints + a new "freshen up" procedure
  11. Parts breakdowns/exploded of the Maytag Neptune front load washer ( mechanical timer models )
  12. Problem chart for MAH3000 & 4000 Neptune washers
  13. Readers repair tips
  14. Trouble shooting tips from the Neptune manual for MAH3000 and MAH4000 models
  15. Tips from our friendly engineer on changing the boot and re-installing that clamp and spring
  16. Tips on changing the washer belt  ( acrobat reader required ) Belt parts link
  17. Tips that show what components need to be checked/replaced if a certain resistor on machine control board is bad. It is as follows: Burnt resistors in Maytag Neptune washer models MAH4000 and MLE/MLG2000
  18. Washing one item in a front load washer
  19. Wax motor helps for the door lock assembly new25.gif
 

Apr 01, 2009 | Maytag Washing Machines

1 Answer

I HAVE AN OLDER MAYTAG NEPTUNE FRONT LOAD WASHER MOD# MAH3000AWA. I AM HAVING TROUBLE WITH IT, IT WILL NOT DO THE FINAL SPIN CYCLE IT SPINS WHEN IT WASHES, AND RINSE CYCLE, BUT THE FINAL CYCLE IT JUST...


Maytag Neptune defective door latch wax motor update
by: Anonymous

The older Neptunes, such as the 2000 Stackers, MAH3000, MAH4000 and the MAH5500A series had some issues which I am sure Maytag has corrected these issues in the newer machines...

There are thousands who have been burnt by the door latch wax motor failure. What happens is the machine will stop spinning because the door latch will fail to lock. Deep inside it is caused by the mechanism that locks the door. The wax motor will draw too much current and damage the control board by burning a resistor (R11) and a triac (Q6).

However, if Neptune owners know to replace the door latch wax motor they can prevent the control board failure from happening. Please tell everyone you know about this important fact.

The older Neptune’s also have a couple additional issues such as the moldy door boot and the reliability of the motor / motor control board. All three of these issues were involved in the class action lawsuit a couple of years ago. See http://www.neptunewaxmotor.com for more Neptune information.

Feb 22, 2009 | Maytag Neptune FAV6800AW Top Load Washer

3 Answers

Maytag Model # MAH4000AWW Neptune Front Load Washer Problem: Door will not lock. All cycles during wash work except the spin cycle.


Clean out your filter after ref. to user's manual. Try some WD40 on the door mechanism (on machine), lock & unlock door 5 or 6 times while machine is off.

May 10, 2008 | Washing Machines

2 Answers

Kenmore front loading washer/NOT SPINNING in cyle


replace your door lock switch it will run fine till you git to final spin then stops if i not missing the point the model no. will start with a 417 even door locks the switch is bad

Feb 24, 2008 | Washing Machines

3 Answers

Maytag mah4000 washer


My machine (Maytag MAH4000aww) failed to drain because of a bobby-pin that was lodged in the drain pump impeller. Because of the added weight of the wet clothes, and the undrained water; the machine would not spin. The Wax motor worked as the door did lock properly, but the machine would "ramp up" trying to spin, but would stop the process when it sensed that the load was grossly unbalanced. Check the drain pump to see that it is not clogged or that the impeller is not impeded by a foreign object before spending money on imbalance switches! I will now cancel the service man, who surely would have charged me for a new pump, plus the cost of the visit, and now I can stop swearing! My wife is glad she married me!!!!
Rene Marchand (Beaumont Alberta)

Jan 13, 2008 | Washing Machines

Not finding what you are looking for?
Maytag MAH6700AWW Neptune Front-Load Washer Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...