Question about Car Audio & Video

Open Question

Wiring diagram sherwood equalizer - Car Audio & Video

Posted by on

  • yadayada
    yadayada May 13, 2010

    we have no wiring diagrams for this device.

×

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 189 Answers

SOURCE: sherwood 460 equalizer hook up

Connect the EQ to the Sherwood as if it were a tape deck: EQ's outs connect to receiver's tape ins (play) and EQ's ins connect to receiver's tape outs (record).
Then you hook the tape deck up to the tape ins and outs on the EQ: Tape deck outs connect to EQ's tape ins (play) and tape deck ins connect to EQ's tape outs (record).
This will put the EQ in your receiver's tape loop.
The CD player should be connected to the receiver though the CD in's and out's (or if your Sherwood doesn't have a CD in/out, then use AUX or TAPE2).
To hear the EQed signal with all receiver sources (like the CD player) you'll need to engage the 'Tape Monitor' button or switch which will route the tape loop to the speakers.

Posted on Jan 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My sherwood rx 4109 has no sound what do i do


Pull the sherwood power cord from the wall for 20 minutes. On the back of sherwood, check all cables and make sure they are in the correct places. Check speaker wires and make sure they are connected. 1)After 20 minutes, turn power on to sherwood. 2) select an input (radio, cd, etc.) 3) Push play. 4) Turn volume to desired level.

Feb 07, 2015 | Sherwood Audio Players & Recorders

1 Answer

I just pick up a used LW 10 Powered sub and 2 channel sherwood receiver.What is the preffered method of hook up up the sub with out a pre sub out?


"Sherwood Receiver" doesn't really tell us much about that end of the scenario.

Look at this picture of the sub amp.

http://cgi.ebay.com.sg/CERWIN-VEGA-LW-10-SUBWOOFER-AMPLIFIER-Speaker-Blade-Amp-/350444290153

You COULD run the Main speaker output to the large Red/Black speaker inputs, then some more wires Out from the other Red/Black connectors to your Main Speakers. That way your amp volume control will affect both equally.

Tweak the sub volume, crossover and phase to match it up to your mains.

May 15, 2011 | Cerwin Vega LW10 Subwoofer

1 Answer

I need a wiring diagram for the pyramid 10 band graphic equalizer. Where can I find this diagram?


Click on MANUAL DOWNLOAD

LOOK PAGE 4 INTO THE PDF FILE!!!!

http://www.pyramidcaraudio.com/sku/903G/10-Band-Half-Din-Power-Booster-Graphic-Equalizer-Amplifier-200-Watts#

Oct 10, 2010 | Pyramid 903G 10-Band Car Equalizer

1 Answer

Sherwood 2000 1st stage leaking. Who repairs? Dealer or can I purchase parts and self repair.


Take it to a dealer! What's your life worth? Self repair can work if you can get the parts, but that's not likely due to liability issues.
Best advice is don't mess with life support equipment.

Leaking can be caused by several thing. Sometimes it minor, sometimes total failure imminent.

ON THE OTHER HAND, if the "leaking" is very slight and is coming from around a little rubber insert in what appears to be a port in the 1st stage, it's supposed to do that! That's how the simple Sherwood regs equalize pressure to ambient. Go figure. Simple.

Jun 11, 2010 | Sherwood Vintage Scuba Service Manual...

1 Answer

Sherwood AX-7030R amp - doesn't switch on.


Something doesn't sound right. The standby circuit is usually very simple. The "regulator" is just a transistor. Can you request and post the parts that he/she can't find. I should be able to get you a source or substitutes.

Dan

Dec 16, 2008 | Sherwood A-965 Amplifier

4 Answers

Sherwood rx4105


you may be using an equalizer? try to pop-up the volume with all tone controls in flat mode. see if it still cuts off. if this is the first time youencounter this then something must be wroing with either your speakers or your amp. unless your ventilation is not good enoughg, you can also try placing a blower on top of your unit to cool it down

May 04, 2008 | Sherwood RX-4105 Receiver

1 Answer

Sherwood 460 equalizer hook up


Connect the EQ to the Sherwood as if it were a tape deck: EQ's outs connect to receiver's tape ins (play) and EQ's ins connect to receiver's tape outs (record).
Then you hook the tape deck up to the tape ins and outs on the EQ: Tape deck outs connect to EQ's tape ins (play) and tape deck ins connect to EQ's tape outs (record).
This will put the EQ in your receiver's tape loop.
The CD player should be connected to the receiver though the CD in's and out's (or if your Sherwood doesn't have a CD in/out, then use AUX or TAPE2).
To hear the EQed signal with all receiver sources (like the CD player) you'll need to engage the 'Tape Monitor' button or switch which will route the tape loop to the speakers.

Jan 09, 2008 | Audio Players & Recorders

1 Answer

Wiring Diagram


Did you get this figured out?

Apr 28, 2007 | Hitron SEQ-554 7-Band Car Equalizer

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4836 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

The Knight
The Knight

Level 3 Expert

73698 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...