Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Whirlpool Du1148XTP Dishwasher

All the green lights were blinking, service man came out and pressed the buttons for awhile and finally went through a cycle. This am none of the lights are going on. I unplugged it for a couple of hours and plugged it in. Heard a "click" and still no lights are going on. I know it's getting power because of the "click". This is a brand new washer and worked fine for a week. (4 complete ok cycles).

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 770 Answers

First off you posted this under the Washers not diswaher section if you have 7 blinking lights on the clean button you have a heater circuit problem

Posted on May 31, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers


All you can do is turn the power off at the power point, leave it for a few minutes and then switch the power back on.

Jan 11, 2016 | Dishwashers

1 Answer

Quiet partner whirlpool III gold reset

Press the "Sani Rinse," "Heated Dry," "Sani Rinse" and "Heated Dry" buttons on the dishwasher's electronic control panel in quick succession to put the appliance in diagnostic mode.
Close the dishwasher door and engage the door latch.
Wait 10 seconds before pressing the "Cancel" button to reset the dishwasher.

Dec 18, 2013 | Whirlpool Gold Dishwasher with Quiet...

1 Answer

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile...

Hi Cathy, we are sorry for the concerns. We would advise service with an authorized servicer. If you would like to schedule service please email us at with your name, address, phone number and model/serial number.

Apr 11, 2017 | Whirlpool 24 in. GU2500 XTP Built-in...

2 Answers

Whirlpool DU1148Xtp DISHWASHER

I lost all respect for whirlpool today, they dont sercive out of warranty dishwashers byt apparently they Have a companies the refer to. This was only after checking the manual and internet for a solution to my clean lught blinking and the dishwasher not starting.

Here is the 105 dollar answer this was the cost of the service call. No parts required only and undocumented conbination of keystrokes that basically does a reset and all should work well.

press heated dry and high temp was together until all the lights on the unit light up then hit cancel. and presto

Hope you find this helpfull

Doug Ernst
El Dorado Hills Ca

Mar 24, 2009 | Whirlpool 24 in. DU1148XTP Built-in...

2 Answers

Whirlpool GU2548 green light flashing, nothing working

I have had the same problem with my the same dishwasher. The manual says that "the dishwasher has malfunctioned. Call service to check heater element". I called service and they are saying that replacing the heater element and possibly the electronic panel may be required. Total cost (part + labor) = $350-400!! I am very very upset with Whirlpool right now.

Jun 11, 2007 | Whirlpool 24 in. GU2548XTP Built-in...

3 Answers

Dishwasher lights blinking

QuietGuard3: Clean light flashing 7 times? Press Heated Dry, press Normal Wash, then press Heated Dry again and press Normal Wash again (that's 4 button-presses) and that should fix it.

May 11, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

9 Answers

Whirlpool gu2400xtpt3

I too had Flashing Clean light and only responded to Cancel light by trying to drain. Whirlpool Model DU1145. I too got problem to clear by pushing High temp,Heated dry, High temp and Heated dry. All lights on display lit up then it went through sequences of all cycles.

May 14, 2006 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal De

Level 3 Expert

2694 Answers


Level 3 Expert

77947 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides