Question about Dishwashers

2 Answers

Zanussi dishwasher DE6744 power indicator light on but when program buttons pressed nothing happens

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Hi,
I had the same problem, in my dishwasher ZDI6895sx the solution to my problem was in the connection between the main PCB and the display/ control pcb on which the buttons/ led's etc are mounted.

On my machine there are about 8 wires in a ribbon type connector which connect the two pcb's, the connection to the main PCB is soldered and on the smaller PCB is a push on fitting, the connections on this pcb are prone to oxidation, there could also be stress on the connector from all of the button pushing, check the connecting wires for continuity with a multimeter if possible but otherwise just remove the connector from the samller pcb clean well(reflow with solder if required) and reseat the connector in its original configuration.

As always only perform this repair if you feel confident and have turned all power to the machine off prior to dismantling.

Let me know how you get on.

Kieran

Posted on Mar 29, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

A printed circuit board (PCB panel) is comprised of electrical components such as resisters, capacitors, relays, and other devices. These components are mounted on the PCB, accompanied by various etched copper wires. You can find PCBs in practically every electronic consumer device from DVD players, to computers, radios, and televisions. PCBs are mass produced and typically come with scored mounts for placement into a device.
1.Place the PCB over the intended mounting location. Press down firmly, applying even pressure across the PCB. Mark the mounting location by pressing a fine tip marker into each of the four pre-drilled mounting holes.
2.Drill the four marked points with a drill and 1/4-inch bit.
3.Attach the nylon washers to the bottom of the PCB with a small amount of adhesive. Then dab the tips of the stand-off spacers in adhesive. Press the stand-off spacers against the nylon washers, aligning the pre-drilled holes with the shafts of the stand-off spacers. Allow to dry.
4.Align the PCB over the 1/4-inch drilled holes. Thread the assembly screws through the top of the PCB, passing through the nylon washers and down the stand-off spacer shafts into the 1/4-inch holes with a screwdriver.Zanussi dishwasher DE6744
power indicator light - 8_17_2012_6_14_27_am.jpg

Posted on Aug 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and...


try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts.

Feb 02, 2011 | Dishwashers

1 Answer

My Zanussi dishwasher DE6744 leaks clean water during the wash cycle. The water appears to be coming from the plastic tank overflow holes, left hand side as you look from the front. Any ideas?


I have the same machine and I took mine outside and turned it on its side and removed the clean water feed and all the screws holding the white plastics off and then un-clipped them off and I saw that there was a blue tube that was leaking on mine, I cut the end off and reattached it with a new clip and hey prestow all working now with no leaks.

Dec 29, 2009 | Zanussi 24 in. DE6744 Free-Standing...

1 Answer

Zanussi Aquapulse DE6854 dishwahser programe lights not working


hi
got same probleme with my aquapulse 4744 slimline

Oct 07, 2009 | Electrolux Dishwashers

1 Answer

Zanussi Dishwasher Model no DE6744 Not working


HI. After me fiddling about with the machine,checkingto make sure water was available to it and trying to locate the float switch (whicu i didnt) .
Then i left it standing overnight aqnd the believe it or not it worked in the morning.
I let it run through the cycles of a program which it did ok.
Hoping it carries on ok. Kenethyorky

Aug 11, 2008 | Dishwashers

2 Answers

Zanussi ZSF 6161 Dishwasher error codes


i have got an zanussi des 959 and showing falt code 5 could u help me out

Jan 19, 2008 | Dishwashers

1 Answer

Won't work


I hant not seen this unit but what it sounds like to me is the control bord that controls the functions on the washer may be bad. you should try and find if there is a tech sheet somewhere in the cabinet or under the dishwasher. that will help you to also see if there may be a fuse or thermal fuse that may be bad. good luck

Aug 05, 2007 | Zanussi 24 in. DE6744 Free-Standing...

1 Answer

Still too long for a cycle


how long does cycle take? if program actually finishes there is unlikely to be a problem. factors which can affect cycle times are inlet water temp and rate water is entering the machine

Aug 15, 2006 | Zanussi 24 in. DE6744 Free-Standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...