Question about LG LSC26905TT Side by Side Refrigerator

Open Question

Help needed to replace water valve & control board

Called LG because water was leaking from the back and found out I had a bad water valve (Metal connection Selenoid), they referred me to an appliance repair company and replaced the water valve. Right after installing the new water valve the front control board/panel goes bad and the dispenser & light quit working also the light inside the freezer. He quits working on it and tells me I have a bad Control board & water valve. Is this something i could be fixing on my own since I think he made it worst? Like a service manual on how to replace the control board and water valve. I have the parts number but i can't find it online: Door: #6871JB1391B Main: #6871JB1410B.
PLEASE HELP!!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
catriver
  • 878 Answers

SOURCE: Water tank inside fridge for water dispenser leaking

peah, I had a couple of these tanks leak. I think they had an issue with this. The last one I had they had a kit where the substitued coiled tubing with 2 john guest fittings to replace the tank. This solved the problem. The part number I have for the tank is 4838jj1003a, you can get it at http://www3.sears.com/ for 17.95. I don't know if they will send you the tank or kit. You can inquire. Catriver...post back.

Posted on Apr 13, 2007

Ad
stradeteox
  • 88 Answers

SOURCE: Faulty ice maker

Hello. Yes, that is the correct position for the icemaker feeler arm. The updated icemaker has a longer feeler arm that hangs down a little more (thereby shutting off sooner when the ice piles up not so high).

Your water leak onto your food is from water spilling out of the front left corner of the ice tray during fill. This has also been updated with a plastic lip that keeps the water from sloshing out when filling up.

The photo shows that your ice tray appears to be unlevel and drooping in the front left corner. This happens with flex tray icemakers over time. The icetray does not fully flex back to its level posiiton. I do not feel you need to replace the entire icemaker. Repalcing just the ice tray should fix your issue.

Hope this helps, please rate my solution.

Posted on Jan 12, 2009

  • 3 Answers

SOURCE: Error Message: Er dH

The error codes are listed in the service manual (p. 32) at the address below:
LFX25960 Service Manual

"Er dH" seems to be a defroster issue.

Posted on Jan 18, 2009

  • 400 Answers

SOURCE: LG GR-292R freezer works/fridge does not.

It is more than likely short of refrigerant, needs to have the leak repaired and then recharge refrigerant.

Posted on Mar 05, 2009

jeffbvegas1
  • 520 Answers

SOURCE: LG ice maker only dispenses crushed ice not whole cubes

Very problematic issue with this model .Try unplugging and plugging the fridgerator which resets the board.The board is located on top under a removeable panel where the power cord enters....there is a reset/diagnostic button on the board itself.Contact LGUSA.com for any possible warranty and complain like crazy to avoid spending $300 on this board which can be purchased from andrewselectronics.com who is a factory authorized parts provider.Keeping that ice maker going will make you pull your hair out which is unfortuante for such a stylish and expensive fridge.good luck

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is a error 50 on a GW709NZ fisher and paykel washing machine


Error 50 Hot water inlet valve fault. Control board monitors the circuit through the valve back to the board. If it gets a bad reading it flags that error. Error 49 for the cold valve. It can be caused by a bad valve. Bad wiring connection (corrosion on plug) or fault on the control board. Most times unfortunately it is the control board that is faulty. You need someone to come & test & find which part needs replacing.

Apr 12, 2016 | Fisher and Paykel Washing Machines

2 Answers

Does not dispense ice or water


Check to make sure you have sufficient water flow through the supply line. If water flow is good then listen closely to the solenoid valve when the water dispenser is actuated. If there is no click the solenoid probably needs to be replaced.

Dec 29, 2015 | LG Refrigerators

1 Answer

Why won't ice tray filling stop?


Michael, I suspect that the water solenoid valve needs replacement--that symptom usually causes either a slow leak and an overflowing ice cube tray or no water flow at all. To test the solenoid valve, slide your refrigerator out and view the back cover. There should be a double solenoid valve down near the bottom back of your refrigerator, one solenoid valve for the water serve spout on the front of the freezer door, and the other solenoid valve for the ice maker. I'd swap the clear plastic lines (to the door water spicket and the icemaker, put a plastic cup under the door water spicket and check in a few minutes for water leaking into your cup--if it does leak into the cup, you've found the problem! There are seval excellent videos on the web covering how to replace the valve, see: http://www.appliancepartspros.com/lg-water-inlet-valve-5221ja2006d-ap4445614.html

That solenoid is controlled by a cam driven switch built into the ice maker motor assembly which can occasionally go bad and need replacement or adjustment, but my experience points to a leaking dirt plugged-open water solenoid valve. Replacment solenoid valves are easy to replace at a cost ranging from $20 to $78 with free shipping to your doorstep--check ebay!

Jun 01, 2015 | LG LSC26905TT Side by Side Refrigerator

1 Answer

I replaced the hot & cold water valves on my LG Washer/Dryer .Now it just humms and no water goes into the washer..What can cause this problem?


have you tried both the cold and hot?hot only has one solenoid while the cold has three.just because it is a new part dose not mean it is not mean it is a good part.try this,turn off the cold and hot water,remove the cold hose from the washer and put it in a bucket and turn it on at the hose bib.if you do not get water,you may have a screen in the hose bib end of the hose.if no screen on that end you may have a metal fitting rusted up just under the hose bib.check the hot side also.hope this helps,if not repost and i will try to dig deeper.thanks

Mar 15, 2014 | LG WM3677HW 3.7 cu.ft. Front Load Washer...

1 Answer

Ice maker stopped working


run service test with volt meter hooked up to the two terminals on water valve if you get a 110 volts to water valve when it is called for and water valve dose not open then the valve is bad. make sure the water valve screen in the end of it is not stopped up.

Jun 19, 2013 | Kitchen Appliances - Others

1 Answer

My LG WM2010CW washer does not fill up with water.


If your washer doesn't go through the washer rinse cycle, the most likely cause is the water valve. What happens is the water valve will stop letting cold water into the washer; therefore, once the washer gets to rinse it will either stop or not do anything during the whole rinse cycle.
This is because when you selected your water temperature, you may have selected warm/cold or hot/cold. The hot water came in and you didn't notice any problems. When it got to rinse, the cold water the cold water won't come in. Therefore, the washer does nothing.
The item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test.
Another test u can do to check the water inlet valve, first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed.
If you still don't have good water pressure, the problem is in your house plumbing and you need to call a plumber. If you had good water pressure the first time you performed the test, the water valve is bad and needs replacing.
TIMER
If your washer doesn't go through the washer rinse cycle the timer may be the problem. Sometimes the timer gets stuck in the middle of the cycle or won't turn at all. If the washer runs, but the timer doesn't turn, the timer is bad and needs replacing.
Do you have anti-flood hoses leading to the machine. If you do there is probably a loose tube in the back causing a small leak. When the hoses detect that water is still flowing after a certain amount of time due to the leak it shuts down and causes the machine to turn off during the rinse/spin cycle
By the way my advice is free cuz God is good!







13821863-0ibogqi43422e0jrk2ickvgv-2-0.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-2.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-5.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-9.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-14.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-20.jpg

Jul 30, 2012 | LG WM2010CW 3.5 cu. ft. Front Load Washer

1 Answer

I have a LG Dishwasher LDF 7811ST with a IE Code Failure after two minutes. I have replaced the Sensor on the side and the flow switch and checked the water inlet filter and still have the code. The next...


IE error usually means the inle valve has failed,However you might want to try a different hose because there is a valve in the lg hoses is you have a grey hose with a chunky bit at the tap end there is a valve inside the hose that often fails.often these guys come back with the motherboard & it doesn't solve the problem.Try ebay for the board they aren't that expensive he has doubled the price of the motherboard anyway.

Apr 26, 2011 | Dishwashers

1 Answer

"nF" error code at end of cycle, and water leak


nf means u have a bad water valve u may also have a bad hose underneath the lid as well if u have water in your control

Mar 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

3 Answers

Water leaking from my front load LG washer


My LG WM2277HB also leaks after 4yrs of use. I found a hole in the front door gasket at the 3 o'clock position. I also have LE errors constantly.

Mar 09, 2009 | LG WM-2277HW Front Load Washer

1 Answer

LG Tromm hot water only


i have found the water inlet valve bad and also the main control board can cause it

Feb 24, 2008 | LG WM-2277HW Front Load Washer

Not finding what you are looking for?
LG LSC26905TT Side by Side Refrigerator Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

christian nielsen

Level 3 Expert

358 Answers

Are you a LG Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...