Question about Canon PIXMA iP5200R InkJet Photo Printer

2 Answers

My pixma ip5200r is flashing green and orange 20 times and then it pauses on the green button, can you help me with maybe resetting it.

Posted by on

  • inhoused May 13, 2010

    Can you give me the waste ink tank reset code. I have tried that in the past and it has worked. I am unable to get it to print or move the cartridge holder over to replace the cartridges.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 560 Answers

Hi. Did you get 20 green and 20 orange? please observe the sequence of flashing lights if its short or long and the sequence, how many orange before it flashes green and how many green before it flashes orange. Thanks.

Posted on May 13, 2010

  • inhoused May 13, 2010

    I get 20 flashing of each colour starting green, orange, green orange this continues for one second each and then after each colour flashing 20 times it stops on the green light for 3 seconds and then starts all over agin.

  • Liza Halbrook
    Liza Halbrook May 13, 2010

    20 flashing lights indicated faulty Logic Board Assembly (Part# QM2-2733). Please have your printer check by an authorized Canon technician to avoid further damage.

    Let me know if you need further assistance. Thank you for using FixYa.


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 369 Answers

If you still can print, it signal's low ink. If it flashes at once, as you turn on the printer and nothing's happen with the printer or no movement or unusable due to error flashing, there is an error either with your ink cartridges (need raplacement) and or hardware mechanical errors. Hope this helps.

Posted on May 13, 2010

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A CANON IP5200R IF I TURN IT ON, YELOW LIGHT FLASES 5 TIMES AND THEN 5 TIMES AND IT GOES ON LIKE THAT CAN ENYONE HELP ME TO FIX THIS PROBLEM


hello leif mo, these are the instructions from the CANON support page Probably your waste ink counter. Should be cleaned or replaced before resetting but usually you can get away with resetting once.
1. Start with printer OFF
2. Hold down RESUME and then hold down POWER
3. Release RESUME
4. press RESUME twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Select functions below with RESUME, execute with POWER

0 presses - green light - Test Print (exit service for i960)
1 press - orange light - EEPROM info print
2 presses - green light - EEPROM initialise
3 presses - orange light - reset waste ink counter.

Hope this answers all your questions Please remember to Rate/vote for any solution that helps you out. Leave a comment if you need more help. Thanks for using Fixya

Aug 09, 2011 | Canon PIXMA iP5200R InkJet Photo Printer

1 Answer

Canon IP5200R printer. Green & red led`s flash 20 times, pause & repeat. print head will not come out of park position on righthand side. Fault occurred while printing a photo error 6500 displayed


Hello!

Error 6500 or green and red flashes 20 times, mean hardware error. Particularly, the Logic Board Assembly

There are two possible fix: first is to reset the printer's waste ink counter and the second is to replace the Logic Board Assembly (part # QM2-2733)
alpug_67.jpg


Reset the Waste Ink Counter:
1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the
Power button. (DO NOT release the buttons. The Power LED lights in green to indicate that a
function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power
button.)
3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)
4) When the Power LED lights in green, press the Resume/Cancel button 4 times (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

For technical help:
  • For toll-free technical support, please call 1 (800) OK-CANON (1-800-652-2666) during regular business hours (currently Monday-Friday 10:00 a.m. - 10:00 p.m. ET, excluding holidays).

  • Toll-free TDD Support Line for the Hearing Impaired is available Monday - Saturday (excluding holidays) at 1-866-251-3752
Hope this helps!

May 18, 2011 | Office Equipment & Supplies

1 Answer

Power button flashing on and off. Maintanence light is on and there is an E, 2, and 4 flashing in the print screen. What do I do? Pleas help!


MP160 resetting errors



1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection



If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response.

Thanks, Joe


Nov 20, 2010 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Many issues, ie, Everything is flashing!


Hi there


yOU CAN ONLY TRY.
not know if it will work so you go to come back to let us know pleas.

Also if you are using the Refillable ink cartilages stop they always cause major issues

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)Note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Turn off the printer.(it must be turn off)
then turn it on again.


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one and to go on helping.
All The Best: Pineworks

Mar 15, 2010 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Error E8 on Canon PIXMA MP 150 printer. It will print on pressing the "diamond" key but needs the same treatment after each print command. What to do?


Hello

Here is something you can try, all credit Ben k:

(1) have your printer power down ie. off, just to make sure pull the plug out and wait 10 seconds.

(2) plug printer back in, now Hold down the Stop/Reset button don't let go.
(2a) push and hold the on/off button

----at this point both fingers are holding down the buttons.----

(3) take your finger of Stop/Reset, pause maybe a second now press stop/reset button once and then press again and hold.

--- both fingers at this point are hold down both buttons----

(4) take your finger off on/off and now finally take your finger off stop reset.

---wait for the printer to go into its service mode ie. wait maybe 30 secs a min whatever till the printer carage has moved back into ints original spot.

---after this has occoured you should be able to press Stop/reset to cycle though the options

each time you press Stop/Reset Alarm and on/off should alternate lighting up. Hope this helps.

0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

Hope this helps good luck

Dec 08, 2009 | Canon PIXMA MP150 All-In-One InkJet...

2 Answers

FLASHING E2


hi,
CANON PIXMA MP160 All-In-One InkJet Printer
has few common problems. Such as Driver CD lost, Scanner does not work, Connection problem etc. For find all these software solution just click here....
75aba9d.jpg3f22050.jpg

http://www.canon.com/printer/prob676ijt65/solution

tonl-i-4

Jul 23, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Error e 27


he method for doing so is worded very badly on alot of sites so I will explain my way.

(1) have your printer power down ie. off, just to make sure pull the plug out and wait 10 seconds.

(2) plug printer back in, now Hold down the Stop/Reset button don't let go.
(2a) push and hold the on/off button

----at this point both fingers are holding down the buttons.----

(3) take your finger of Stop/Reset, pause maybe a second now press stop/reset button once and then press again and hold.

--- both fingers at this point are hold down both buttons----

(4) take your finger off on/off and now finally take your finger off stop reset.

---wait for the printer to go into its service mode ie. wait maybe 30 secs a min whatever till the printer carage has moved back into ints original spot.

---after this has occoured you should be able to press Stop/reset to cycle though the options

each time you press Stop/Reset Alarm and on/off should alternate lighting up. Hope this helps.

0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

Feb 26, 2009 | Canon PIXMA MP150 All-In-One InkJet...

4 Answers

Canon mp150 pixma printer error e5


dear warenout

try this methode

Methode 1

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting formenu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection


that's all


maybe it can fix your problem



thanks


cropp

Mar 12, 2008 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Canon BJC 8500 WASTE INK FULL


.
How to Reset Waste Ink Protection Counter Canon Pixma IP8500 Printer

Instructions:
Resetting Waste Ink Counter Canon Pixma IP6000, Canon MP450, Canon Pixma IP8500

1. Turn off the printer.
2. Whilst pressing Resume button also press on POWER.
3. Then Press RESUME button and release POWER.
4. Then Press RESUME button again .
5. Then release all buttons.
6. Led Indicator should be green and stay green.
7. Click RESUME button 4 times if you wish to try again.

Then See Table Below:

Orange - Service test print ONCE - Orange - Service test print.
Green - EEPROM information TWICE - Green - EEPROM information print.
Orange - EEPROM initialization 3 TIMES - Orange - EEPROM initialization.
Green - Waste ink counter resetting 4 TIMES - Green - Waste ink counter resetting
Orange - Destination setting (Press Power then Press Resume 3x) 5 times - Orange - Destination setting (Press Power Press Resume 3x)
Green - Print head deep cleaning 6 TIMES - Green - Print head deep cleaning.
Orange - Green, Orange - Return to menu selection 11-13 TIMES - Orange, Green, Orange - Return to menu selection.
Green - Left margin correction 14 TIMES - Green - Left margin correction.

8. Turn off printer.
9. Restart Printer.
Good Luck!

Tinteiros - Magic Inkjet Flush (Ebay)

Nov 07, 2007 | Canon BJC 8500 InkJet Printer

2 Answers

CANON PIXMA MP150


Error E/2/7 Solution=waste ink basket
Mp150
Reset Counter
Service mode operation procedures -
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

Sep 03, 2007 | Canon PIXMA MP150 All-In-One InkJet...

Not finding what you are looking for?
Canon PIXMA iP5200R InkJet Photo Printer Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1973 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...