Question about Jandy AquaLink RS2/6 All Button Dual Equipment -

1 Answer

Select button on Jandy Aqulink rs does not work

Jandy Auqulink is working fine except the select button does not seem toconnect to any command . It has a full battery charge.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 310 Answers

We have been repairing quite a few of these controllers lately. Much lower cost than replacing the boards. Best Regards, bruce@fixyourboard.com

Posted on Jun 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the Jandy RS6 Intellitouch Controller Extra Aux / Solar power plug always ON/Powered?


Your logic seems workable...
(I got nothing ... should work).

Trouble shooting says to check & clear "phantom"
programming... (Pg. 30: sounds like hokum 2 me).

My best advice..
Go to page 40 and contact their customer support.

Jandy AquaLink RS Installation Manual Warranty

1-707-776-8200

Carnac the Magnificent

Jun 22, 2014 | Jandy AquaLink RS All Button, Wired, RS6...

1 Answer

My jandy is frozen and says firmware b13. HELP!!!!


check to see if cut wire going to aqulink to antenna if ok then reset system

Jul 20, 2011 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

On my all buttom qualink 4 on my buttons work except when I turn the spa off the cool down mode doesn't seem to work it says heater will turn off after cool down but the jandy doesn't turn back to filter...


Your heater should shut down rite away and the pump will keep running to pump cool water through the heater. After the cool down period then the valves will go back to normal run positions.

Nov 04, 2010 | Jandy AquaLink RS2/6 All Button Dual...

2 Answers

My aqulink rs says check AquaPure General Fault Filter pump.... What does this mean and waht do I do?


time to clean the filter time to check for basket clean or the salt chlorination cell give up time to replace them

Aug 16, 2009 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

AQULINK CONTROLLER WILL NOT TURN OFF FILTER PUMP


Sounds like one of the relay's has gone bad inside the box. If your lucky you can move the wires to another relay if there is one available. Make sure you move the top wires too, not just the 4 bottom wires, or you will have to do some reprogramming.

Mar 14, 2009 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

Not finding what you are looking for?
Jandy AquaLink RS2/6 All Button Dual Equipment -  Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

8688 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Jay Finke
Jay Finke

Level 3 Expert

1384 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...