Question about Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Won't start up...

Door is locked, power is on, press and hold the START button and the damn thing dings 3 times and just sits there...practically brand new, I'm on a cattle ranch with filthy clothes everyday, and I'm not pleased...

Posted by on

  • Timberspike Mar 29, 2008

    Could be...guess I need to sched a $&@%#$! service call to find out...

  • Timberspike Mar 29, 2008

    1) Cord is plugged firmly in...
    2) No fuses are blown, no power is out...
    3) Water supply is turned on...
    4) Door is firmly shut

    I'm in the process of leaving the cord unplugged for 30 mins to see what happens then...I thought Whirlpool was more reliable than this...

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

HI,

If THE WASHER DOES NOT START THEN HERE ARE THE POSSIBLE CAUSES AND SOLUTION FOR IT.

1)Electrical power cord may not be plugged in or connection
may be loose.
Sol: Make sure plug fits tightly in wall outlet.

2)House fuse is blown, circuit breaker tripped, or a power
outage has occurred.
Sol: Reset circuit breaker or replace fuse.
Do not increase fuse capacity.
If problem is a circuit overload, have it corrected by a qualified electrician.

3)Water supply tap is not turned on.
Sol: Turn on water supply tap.

IF THE WASHER DOES NOT SPIN THEN:

1)Check that the door is firmly shut.
Sol: Close the door and press the Start/Pause button. After pressing the Start/Pause button, it may take a few moments before the clothes washer begins to spin. The door must lock before spin can be achieved.

if the door is not unlocked after 6 trials the central control unit will enter a failure mode and the digital display will show FdU
If this happens then reset it by unplugging the all the cords
for 30min and then plug it back.

Goodluck,
Please don't forget to rate the solution.

Posted on Mar 29, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,894 Answers

This is due to the door sensor not working

Posted on Mar 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My BMW Z3 I took the battery out now my doors will not lock or unlock but if I try to unlock door car will not start but if I disconnect the bat and put back and don't try doors it will start I need...


Put your key in the ignition switch it on and back off remove key no PRESS AND HOLD UNLOCK BUTTON without releasing the unlock button press the LOCK button 3 times within 10 seconds doors should lock and unlock rapidly to confirm it worked you must do this sitting in the car with doors and windows locked

Apr 07, 2014 | Cars & Trucks

1 Answer

Maytag maxima door locked


Similar problem here - pump was set for a 58 minute normal cycle, I look in and see it is now showing 67. Hmm. Attempt to shut it off because it is just sitting there pumping and pumping. Power shuts off but pump keeps running and add garment light flashing red. Cannot open door (to add garment or not) Unplug the unit and the door will not open. Anybody got a clue what's up? I have a wash in, service is closed due to a storm today. Just bugs me that it is 6 months old and seems to act up a fair bit electronically.

Dec 09, 2011 | Maytag Washing Machines

1 Answer

Kitchenaid kudi01ilwh2 won't start


By won't start do you mean that everything is set ok but when you press Start button then nothing happens.

In that case most likely the door is not sitting properly or the door latch or door switch is faulty causing the dishwasher to not start.

However, if nothing happens on the panel when you press buttons but power is there, then most likely the panel is faulty and can be replaced.

you can trace the parts in these diagrams.

Nov 01, 2011 | KitchenAid 24 in. KUDS01FLSS Built-In...

2 Answers

Key is flashing all the time. Its completely locked me out. It won't let me do anything. I've tried switching it on and off again like you do with computers to no avail. Please help. My machine is...


If its showing a key symbol then the child lock is on.Press and hold the start/pause button in for several seconds and this should take the child lock off and start to work again.

Jun 02, 2011 | Bosch Classixx WFL 2066 Front Load Washer

2 Answers

How do I program a Viper 473 V Replacement Remote, to my 2004 Hyundai Santa Fe?


Set lock/unlock button

· open drivers door

· turn key to ON position

· press valet switch 1 time

· press valet switch again and hold

· when alarm chirps press lock/unlock on remote

· release valet switch

· turn key off

Oct 05, 2009 | Viper Security and Remote Start System...

1 Answer

Programming a micro chip key for a 2007 malibu


Key FOB programming is definately not a dealer only job, as much as they'd like you to think it is!:disappoin Try this procedure. It's a pretty standard procedure across the GM line: (write-up compliments of nat3ten from trailblazer forum)


"1 SIT IN VEHICLE AND CLOSE DOOR

2 HOLD FINGER DOWN ON UNLOCK POWER DOOR LOCK SWITCH ON DRIVERS DOOR.

3 put key in ignition, TURN IGNITION ON / OFF , ON / OFF.LEAVE KEY IN IGNITION.(DO NOT START VEHICLE, ON POSITION IS THE POSITION BEFORE START)

4 RELEASE FINGER FROM POWER DOOR LOCK.POWER DOOR LOCKS WILL CYCLE.(JUMP UP AND DOWN)

5 PRESS AND HOLD BOTH THE LOCK AND UNLOCK BUTTONS ON NEW REMOTE UNTILL YOU HEAR POWER DOOR LOCKS CYCLE.(JUMP UP AND DOWN) YOU MAY HAVE TO HOLD BOTH BUTTONS DOWN FOR 5- 20 SECONDS.

6 TAKE 2ND NEW , OR OLD REMOTE AND HOLD BOTH UNLOCK AND LOCK BUTTONS DOWN UNTILL LOCKS CYCLE.(MAY TAKE 5- 20 SECONDS)


7 TURN KEY ON, THEN OFF.
YOU ARE DONE, EXIT VEHICLE AND TRY YOUR REMOTE."

Jun 30, 2009 | 2007 Chevrolet Malibu SS Sedan New Cars

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

2 Answers

Need to reset the key fob


Sit in the driver's seat
Close all vehicle doors; ignition key should NOT be in the ignition, and ignition should be OFF.
Press and hold UNLOCK on your driver's door lock switch, insert and remove your ignition key TWICE, and insert the key in the ignition; this time LEAVE IT. DO NOT TURN THE KEY!!
LET GO OF THE DOOR SWITCH; listen for 3 dings after which, with the key still in the ignition, you will press and hold both LOCK and UNLOCK AT THE SAME TIME on your transmitter for 12 seconds. or until you hear 2 DINGS which indicate a newly programmed transmitter.

If you wish to use more the one transmitter (4 MAX), press and hold lock and unlock just as the first transmitter.

PULLING OUT THE IGNITION KEY ends this procedure :-) !

May 01, 2009 | 1998 Buick Century

3 Answers

Whirlpool gold start button flashing dishwasher won't start


press sani and heat back and fourth then after all lights light close door and hit start then wait about 3 minutes. worked for me

Oct 12, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

5 Answers

Kenmore dishwasher Lock On light flashing


holding the button for four seconds will not do it, you have to hold it until the light stops blinking and
will go back to normal, normall takes more than four seconds to unlock the unit, this is something
the sears repair techs know becouse the are trained on all this things but, they will not share this things, becouse thats how they make money

Dec 29, 2007 | Dishwashers

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

prem mathew

Level 3 Expert

662 Answers

yadayada
yadayada

Level 3 Expert

71231 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...