Question about Proform Crosswalk 500 Treadmill

1 Answer

While trying to run the mat/track stops or studders momentarily.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Proform Master
  • 832 Answers

If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift the edges of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

Posted on May 16, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bwinton
  • 83 Answers

SOURCE: While trying to run the mat/track stops or

Sounds like the belt is loose. To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need transmission, center console, and floor mats for 2001 Sonoma SLS...


is this an extended cab ,4wd,automatic or manual transmission ,,studdering can be anything from needing a tune up --tires balanced -motor mount-suspension- c/v axle --u-joints torque converter-rear -transmission clutch-4wd components etc

Oct 24, 2016 | 2001 GMC Sonoma

1 Answer

How do I access tone arm belt and motor on a Pioneer PL-L30 turntable?


Try lifting up the turntable mat. You should see a hole. Note how it fits before removing the belt.

Oct 10, 2014 | Audio Players & Recorders

1 Answer

My 97 bonneville studders and stops running when engine gets hot 190-200 degrees


Hello. It seems either your water temperature sender is malfunctioning or your ignition module is overheating.

Apr 01, 2014 | 1997 Pontiac Bonneville

1 Answer

The mat where we run in this cardio machine . The mat is always sliding to one side only so it is always stuck while doing cardio . How to fix it?


there should be a alinement bolts at the track end if the track is running to the right you need to tighten the left side .if that is tight all ready you need to loosen the right side. the track will run towards the tightest side. open the end up and you will see the bolts .

Dec 27, 2012 | Garden

1 Answer

My 97 Legacy started to studder when stepping on the gas from a dead stop. It does not seem to studder at higher speeds. Do you thing the Fuel filter may need to be changed?


My 97 Legacy started to studder when stepping on the gas from a dead stop. It does not seem to studder at higher speeds. Do you thing the Fuel filter may need to be changed?

May 10, 2010 | 1997 Subaru Legacy

1 Answer

While trying to run the mat/track stops or studders momentarily.


Sounds like the belt is loose. To tighten the belt, start by locating the two bolts that adjust the rear roller (one on each side of the unit in the back). Run the unit at about 3 mph. Tighten the bolts a 1/4 turn at a time. Make sure that what you do to one side, you MUST do to the other side or the belt will get off center. After you tighten it 1/4 turn, check the belt to see if it is still slipping. If it is then tighten the belt 1/4 turn again. Continue until the belt does not slip, but do not tighten the bolts more than 2 full turns.

Mar 17, 2010 | Proform Crosswalk 500 Treadmill

1 Answer

Vehicle stalled out while driving, will not kick over


There is no carb, either throttle body or fuel injection.If it was fuel related it would not cause all the lights to come on.Sounds like electrical and will have to be tracked down and diagnosed. Your computer may have gone out but that has to be diagnosed.

Aug 05, 2009 | 2002 Chevrolet Blazer

1 Answer

Sharp CD-DP2400 3-disc mini component system stops playing in first track


the rails on the laser slead need cleaned..the grease gets hard/dirty and stops it from moving skip it to track 16 to move the dirt off the track..

Oct 26, 2008 | Audio Players & Recorders

Not finding what you are looking for?
Proform Crosswalk 500 Treadmill Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...