Casio xj-s36 flashing red power light; temp and lamp LEDS flash

1. VR2/VSI DIAGNOSTIC FLASH CODES

# OF LEDS
CODE
CAUSE
POSSIBLE SOLUTION
One red LED
1
Low battery voltage
Charge batteries
Two red LEDs
2
Left motor open
Make sure left motor is plugged into controller.
Three red LEDs
3
Left motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs One yellow LED
4
Right motor open
Make sure right motor is plugged into controller.
Three red LEDs Two yellow LEDs
5
Right motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs Three yellow LEDs
6
Inhibit active
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs
7
Joystick error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs One green LED
8
Controller error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs Two green LEDs
9
Brake fault
Make sure both motors are plugged into controller.
Three red LEDs Four yellow LEDs Three green LEDs
10
High battery voltage
Contact your authorized Pride Provider.
What if the speed LEDs on the VR2/VSI begin to flash?

• Determine if the battery charger is connected to the power base. When the battery charger is connected to the power base, a charger inhibit feature keeps the power chair from driving. This is indicated by the VR2/VSI speed
  LED(s) flashing.
• Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to
  activate.
• Determine if all controller connections are plugged into the power base properly. If the 3-pin charger
  inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

Hello,

In attempts to get your IN15 projector working, please try the steps below.

Disconnect AC power from the projector and wait for 10 seconds for supply to properly discharge.

While holding down the Menu, Select and Input buttons simultaneously, plug in the main AC power until

the LEDS stop flashing (approximately 7 seconds)

Kindly get intouch with Cinesonic Audio Visual Pvt. Ltd. in New Delhi at 10/2, DLFIndustrial Area, Shivaji Marg, Moti Nagar,
New Delhi-110015

Contact: ' Board: +91-11-47424444 (30 Lines)'

e-mail: Robert@cavpl.com

For any problem related to Casio Projectors

Sounds like your bulb has gone.
Unplug it.
Clean all the filter.
Remove lamp and inspect it, check for darkness, cracks and if filament has blown.
If lamp looks ok, put back in and test.
Dont touch the lamp front glass with your fingers as this can damage lamp.

---

Please dont forget to vote this answer was helpful

Many thanks

------

hello When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for
the picture to appear on-screen. See "IMPORTANT NOTICE ABOUT HOT LAMP R
When the TV has been powered on long enough for the lamp unit to get hot, it may take several minutes for the picture to appear on-screen
in the following situations:
• When the Quick Restart™ feature is set to OFF and you turn the TV off and then on again within a few minutes.
• If the TV is on when a short-term power failure, power surge, or other similar power failure occurs, such that the TV loses and regains
power within a few minutes.
This is a property of DLP TV lamp technology and is NOT a sign of malfunction.
If this occurs, the green LED on the TV front panel will blink (and the red LED will be lit solid) until the TV is finished restarting the lamp
and the normal picture appears. If BOTH green and red LEDs are blinking at a one-second rate, you will need to turn the TV off and then
on again to restart the lamp.
ESTART" on page 8. if this no good check the lamp in side to see if it's not burn't out good luck

regards
shaun

replaced the lamp

it wasn't able to go through cooldown mode. turn it on, power down and let it go through cooldown. does the light come on at all?

lamp duration

This should fix the drum light being on that 1720

Turn off the power using the switch on the back of the printer. Open the front door of the printer. Hold Continue button down, power on the printer, and continue to holding Continue down until the LEDs begin to flash. When the LEDs start to flash, release Continue button. The LEDs will continue flashing until only Error LED will be lit. Close the front door. Continue, Ready/Data, Toner Low and Load Paper LEDs should be lit. Wait till the printer completes the POST process. POST is complete when fan noise and rollers stops. After POST wait for 5 seconds Press Cancel button 4 times slowly until the Toner Low LED is lit. This is the procedure resetting the counter. Press and hold Continue until all LEDs begin to cycle in sequence, then release Continue. Now only the Toner Low LED will be lit. Cycle the power of the printer: Remove the power cable - Wait for 5 seconds - Plug the power cable back to the printer - Power the Printer on.

You have to disconnect power to reset it.