Question about Behringer Pmp3000 16 Channel Audio Mixer

2 Answers

How to get the effects to work on the mixer

Im pretty new at this...Just got a new Xenyx behringer 16 input mixer and got everything to work...Just trying to figure out how to add a little reverb to the voice and cant seem to figure it out...Says it has effects included in the mixer. Not to sure how fx works and manual doesnt go into any kind of detail I find...Thanks for anyone that can help..!!!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

The efx master and channel efx send are the same usually the sane color. Whatever channel the mic is in turn the efx knob on the channel up and make sure the efx master is up

Posted on Dec 22, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Behringer Master
  • 5,603 Answers

This is in general for Behringer mixers since you did NOT tell us a model number...

To use the effects you adjust the FX knob for EACH channel for the amount of the mic or input you want to send to effects from that channel. This is the "send" mix.

You dial in one of the effects based on the list near the effects selection window with the selector knob and the number will change and start flashing. You press down on the selection knob which will enter the new effects number and the number will be solid and not flashing.

Then there is a knob to select how much of the OUTPUT of the effects you want to go to the main and sometimes one for the amount to the monitors.

That is all there is to it. The effects can be gated by a foot switch input if you desire.

It is a good idea to include a model number as your thing is posted as if it is a PMP3000 mixer.

Posted on May 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My behringer xenyx 802 premium 8-input mixer worked fine for 1 day but now it sounds watery and behringer support was no help at all


Sounds like it may have failed. Yes, it is likely that it needs to be returned. Another option is to unplug all inputs and outputs. Plug in ONE device into the board, and use the headphone jack on the board. Does it sound the same? Just basic troubleshooting may help.

Oct 02, 2012 | Behringer Xenyx 802 8-input 2-bus Mixer W/...

1 Answer

Behringer Xenyx 502 Mic buzzing...PLEASE HELP


Get yourself anti-static spray and spray over the connector before inserting into the jack, most times its dust or static buildup which causes that buzzing sound and in other times replace your mic

Mar 02, 2012 | Behringer Xenyx 502 Audio Live Music Mixer...

1 Answer

Can I use a footswitch for the reverb, to allow me to switch it off when talking ON MY Behringer Xenyx 1202 FX


Sorry, the Xenyx1202FX does not have a footswitch input. I would suggest if this function is needed to use an external FX unit which has a footswitch input.

Apr 26, 2011 | Behringer Xenyx 1202 12-input 2-bus Mixer...

1 Answer

I have a Behringer eurorack ub1002 mixer. how can i open it up to fit a new socket on the face of the desk. I seem to have unscrews all the screws


One has to remove all the knobs, including the faders. There are MANY screws through the panel AND all the 1/4 inch jack hardware has to be removed. Remove EVERYTHING else BEFORE removing the small screws... It is a LOT of work, although this mixer is small compared to some! Be careful to NOT scratch the circuit board as Behringer uses very small/narrow circut traces that are easily damaged. Make sure you have the EXACT same socket so it not only lines up with the holes but is the right height from the circuit board, Temporarily mount the socket along with the mating ones before soldering the pins so it is in perfect alignment to fit the hole in the panel.

Jan 25, 2011 | Behringer Xenyx 1002fx 10-input Mixer W/...

1 Answer

I cant get any output in sonar 6 ahd yes the rack is active im new to sonar just the mixer xenyx xl 1832 usb


Make sure Sonar is set to use the Xenyx for the clock in the audio options pull down menu. It often defaults to your PC soundboard.

Sep 23, 2010 | Behringer Xenyx 1832fx Mixer 18 Input 32...

2 Answers

Xenyx 1002fx Mixer 10 Input 2 Bus with Efx: behringer mixer power goes off after running about...


Problem is likely thermal. Open unit carefully and use freeze mist (circuit cooler) to find bad component.

With that long a time period, it is possibly a component mounted on a heatsink.

May 18, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

Im try'n to hook a ''Duel fex pro'' multiband sound enhancement processor model ex 220, to my berhinger xenyx 1222fx mixer?


Use four (4) TRS cables. Connect from the
AUX "send" (left and right) to the input of the effects unit with two of the cables. Use the other two cables to connect from teh effects out jacks to the AUX "returns" left and right.

Mar 23, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

3 Answers

Iam trying to make my behringerXENYX 1204fx mixer, / connect


I have trouble my new behringer xenyx 1204FX VU led dead , like new VU it must play , how to repair this unit VU light

Mar 13, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

3 Answers

How do i hook 1202fx to computer?


just connect a baby plug to rca from the pc to the mixer respectively

Feb 14, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

Not finding what you are looking for?
Behringer Pmp3000 16 Channel Audio Mixer Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Ben Armstrong

Level 2 Expert

334 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...