Question about Dishwashers

2 Answers

I have a hobart sr24h dishwasher that does not rinse or wash with any food off the dishes.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

It may be the wash impeller disk broke off, and cut into the bodywash pump housing. Remove the 8 screws(4 long into the posts and 4 short, into the lower cover) to remove the wash arm support. Look each side of the wash impeller on the lower housing for a slot cut, Check the wash arms for small pieces of grey plastic from the impeller disk.. Make sure the fill flow rate is 20 PSI. If your water is hard, the booster and vacuum breaker may be restricted with lime buildup. Remove and clean as required,

Posted on Aug 03, 2009

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 68 Answers

Check inside your wash arms for debris. Remove them and clean them out.

Otherwise, the wash impellor may be bad.

Mike

Posted on May 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Hobart am 14 with a new pump motor drawing high amps


Search Results

    Dishwasher Electrical Problems - Chapter 6 - Dishwasher ...

    www.appliancerepair.net/dishwasher-repair-6.html
    If the dishwasher is loaded with a lot of food residue, it will need extra rinse cycles .....changes, they will be explained in instructions that come with the new timer. ... If you have an ammeter, the stalled motor will be drawing 10 to 20 amps or more. ... Since the resistance of the heater is very high compared to the resistance of ...

    Pump Repair FAQ - OTP Industrial Solutions

Nov 26, 2015 | Hobart Dishwasher Am-14 Commercial Dish...

1 Answer

Hobart SR24H dishwasher after rinse cycle the same time pampas water in and out of the dishwasher, two pipes are opened and working


Hello.
As per my personal opinion this is normal because for the final rinse you have a small booster or boiler..
When you turn on the machine..it starts fill and also the booster for the final rinse.
You start the machine..wash cycle...rinse cycle..
Now..new water(from rinse booster) is coming on the tank in order to rinse the dishes..on the same time the machine drains the excces water from the rinse(over flowing) and fills up the booster with new water.
Should be like this

Good luck

Jun 29, 2013 | Dishwashers

1 Answer

I have a am-14 hobart washer. having problem with rinse temp indicator. it is fine for the wash then the temp gauge is jumping around, could it be the thermostat?


Your rinse temperature sensor that is a tiny probe in the water piping (top rear of machine) needs replaced. Hobart part # 00-294692. It costs about $84.

Oct 19, 2012 | Hobart Dishwasher Am-14 Commercial Dish...

1 Answer

My sr24h hobart undercounter dishwasher is stuck in a mode where all it does is drain water out. Will not do anything else...???


Hello There; If your unit stuck on the wash cycle and not advance to rinse cycle because the rinse water is not up to 180 degree . You've to check out the booster element and the rinse temp. I hope this will help.

Sep 19, 2010 | Hobart SR24-H Built-in Dishwasher

1 Answer

Hobart WM-ID dishwasher doesn't heat water enough to clean dishes


The WM-1D does not have any internal heating devices. You have to supply the machine with the proper water temp. It has two fill valves, one for wash and one for rinse. It should have 150F supplied to the wash fill valve and 180F to the rinse fill valve.

Feb 04, 2010 | Hobart AM14C-155 Dishwasher

1 Answer

Hobart SR24H dishwasher will not spray, arm does not rotate


ck. flow press. of water , when fill solenoid opens press. should be @20 p.s.i because this is a time fill machine. this is important .not static press. flow press. also ck the screened washers in the fill hose to see if they are plugged .let me know what you find so i can futher assist. dont forget to vote tks

Jan 10, 2010 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Not cleaning dishes


Our Bosch does a pretty good job of washing dishes. But we rinse most of the time. Not a hard rinse, but a rinse.

Are both spray bars rotating? You can test by seeing that the bars rotate easily by hand, and also by starting a cycle and opening the door real quick when you hear the spray hit the door.

Make sure the spray bar nozzles are all clear.

Has it ever done a good job of cleaning dishes?

DI you leave a heavy build-up of food on the dishes, and allow it to dry before washing?

Jan 26, 2009 | Bosch SHU5315UC Dishwasher

1 Answer

Hobart LX30H washing to hot.


what temp is it washing at. washing should not be the problem. This machine is designed to rinse at 180 degrees + to sanitize dishes. The machine could be converted to a chemical sanitize, it would use bleach in the rinse water instead of 180 degree water to sanitize.

Sep 04, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

2 Answers

Indesit D63 dishwasher dishes not getting clean


Dishwasher seems to cycle through but dishes are still dirty, like there is no water being sprayed?

Jan 23, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...