Question about Brother HL-2070N Laser Printer

1 Answer

Brother hl-2070n green ready light is on solid(green)....fan is on but unit will not print

Posted by on

  • 3 more comments 
  • wove792002 Oct 07, 2008

    Green Light on and the fan is going, I tried pressing the go button but nothing.

    What is going on?

  • Anonymous Oct 10, 2008

    Same problem. Green light on steady. Fan on. Computer says it printed. Printer does absolutely nothing.

  • Anonymous Oct 11, 2008

    Tried everything cannot seem to get it to print

  • tamathat Oct 11, 2008

    i am having the same problem, cannot seem to get it to work at all

  • MoZannBeak Jan 22, 2009

    My problem is the same, however a couple more things noticed. It appears the printer goes into a printing mode and then can not back back out. If I delete the printer from the printer area of the comp after unplugging power and usb from comp. Then plug printer back in and power up. Right after installs driver and is ready for use, the Brother printer tool finds the printer and gives the info needed. Start to print test page or hardware test page and can no longer communicate with printer with info tool. So seems is stuck trying to print even though comp sees print job as complete. Fan stays on, green LED did blink indicating received data, goes solid indicating done, but nothing printed.

    Also noticed if pull the toner out, and power cycle the printer, it notices that the toner is missing and LED's light accordingly. but if close door without putting in toner, green LED lights up as if ready but since no toner it most def is not. if dont power cycle can open door and no error (Red Paper LED) occurs as would normally either.

    Seems to be a sensor or something broken hardware wise, but cant find a service manual to show me where to start looking. As switch toner, drum unit to second Brother printer, all works fine, and none of the same effects.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 159 Answers

The printer is ready to print. Pressing control panel button wakes up the printer to Ready mode

Posted on Apr 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HL-2035 ALL Leds light up solid


Try resetting the printer. Disconnect power and reconnect after a minute. If not ok, make sure the drivers are uptodate.

Nov 27, 2013 | Brother HL-2070N Laser Printer

1 Answer

When I print with my brother hl-2070n...the print out is very very faint. i have changed the toner and drum...any suggestions?


if you printing is just faint, need to replace toner, but if your printing is faint and blurry, need to add grease to the fuser film roller, need advanced skills for that, disassemble the fuser unit take out the fuser film and put some special high temp grease on the heating element, assembly all back and install, the other way is replacing the fuser unit

Mar 12, 2013 | Brother HL-2070N Laser Printer

1 Answer

Toner light is on


nonexxx provides solution to this problem at the following:
http://www.fixya.com/support/t454872-toner_light_go_away
1. Power Unit off

2. Open front cover

3. Press and hold GO and turn power on

4. When all 3 lights lit release and press GO twice

5. All lights turn solid

6. With all solid, press GO 5 times

7. Ready light GOes red

8. Close door and you're all set at

Jul 05, 2010 | Brother HL-2070N Laser Printer

1 Answer

Brother HL-2070N Laser Printer Will Not Print


First of all, I checked the answers given here, but nothing worked; everytime I turned on the unit, the red light flashed that the printer was out of paper.

From the Brother's HL-2070 manual, in the troubleshooting section: take out the toner cartridge from the front of the machine (be careful, any black toner powder that come off may be very difficult to clean up). I took the toner cartridge to the sink.

There is a blue slide along the top of the unit that will clean the corona wire if you slide it back and forth, from one end to the other (toner/dust can become caked on the wire over time; sliding the slider back and forth simply knocks the caked off 'stuff' off of the wire).

Replace the toner cartridge; it worked fine for me. I was immediately able to print.

Mar 11, 2010 | Brother HL-2070N Laser Printer

1 Answer

Brother HL 5250 red light flashing


I found this solution on the web-- Hope it helps.

The HL-2070N gets stuck in a toner end-of-life error condition. Perform the following to clear :
With paper loaded, new toner in,

Open front door
Turn off printer
While holding down the GO button, turn printer back on
When all four LEDs light up release GO button. All LEDs will turn off
Press the GO button 2 times. The 3 LEDs (toner, drum, paper) will light up solid
Press the GO button 5 times
Paper light will be blinking
At this point the toner end-of-life condition has been reset. Close front door.
BTW, I got this from Brother Support. Also, just a reminder, timing is important here so don't pause between button presses.

Jan 28, 2009 | Brother HL-2070N Laser Printer

3 Answers

Brother HL 2070N Drum Unit changed but printing with dots on the left hand side


If toner leaked into the machine and got on the fuser that could cause this, but the dots would go away after a few prints. Try another drum unit.

Oct 28, 2008 | Brother HL-2070N Laser Printer

1 Answer

Brother HL-2070N Will Not Print


Hi tom8972
try to reinstall the driver of it.

hope this helpful for you,
thanks,

Hamedo

Sep 13, 2008 | Brother HL-2070N Laser Printer

1 Answer

Brother HL-2070N


make sure the protocall is enabled for your specific printing preferences.

if not sounds more a computer issue.

May 16, 2008 | Brother HL-2070N Laser Printer

4 Answers

HL 2070n


Copier tech here. :P I just had to look this up. looked to the internet first, before going to find a manual.

open front door (the door for toner and drum units)

hold Go untill all four lights are on.

Release Go

Shut door

good to go.

Have a good night ya all.

Mar 28, 2008 | Brother HL-2070N Laser Printer

Not finding what you are looking for?
Brother HL-2070N Laser Printer Logo

Related Topics:

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...