Question about Whirlpool 24 in. DU1100XTP Built-in Dishwasher

2 Answers

Dishwasher won't reset, stays on gree-flashing light- Clean cycle

Cannot get my WHirlpool -gold, Quiet Partner III to re-set.
It got froze in the middle of a cycle ( someone opend door and didn't shut.)
SO when I hit the reset, it cleared the cycles, but only flashes GREEN in the clean button. If I try to puah a normal wash cycle, nothing happens.
I turned the main power on/off...still flashed on Green-clean cycle.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 949 Answers

HI,

This is an indication that the water did not heat properly. I have put together some instructions on what can cause this and how to reset the control so you can use the dishwasher again. Follow the link below and let me know if this helps.

http://www.fixya.com/support/r4628906-flashing_or_blinking_green_clean_light_7

Posted on May 11, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.

http://www.appliancerepairlesson.com/dishwasher-2/dishwasher-clean-light-blinking-7-times/

Good Luck

http://www.appliancerepairlesson.com

Posted on Mar 06, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool Quiet partner V Dishwasher will not start no lights ,,,nothing


Try unlatched door and hit heated dry, normal, heated dry, normal all within 3 seconds of each ither. Close dior, latch and try again.

Mar 02, 2015 | Whirlpool Gold Series Quiet Partner Iv...

1 Answer

Quiet partner whirlpool III gold reset


TRY A RESET CODE
Press the "Sani Rinse," "Heated Dry," "Sani Rinse" and "Heated Dry" buttons on the dishwasher's electronic control panel in quick succession to put the appliance in diagnostic mode.
Close the dishwasher door and engage the door latch.
Wait 10 seconds before pressing the "Cancel" button to reset the dishwasher.

Dec 18, 2013 | Whirlpool Gold Dishwasher with Quiet...

1 Answer

I have a Whirlpool gold Quiet partner III. The Normal button of the cycle is blinking and I can't start the dish washer. What is going on?


most likely the door switch is not making contact or is faulty. Shut the door tightly and see if it makes any difference.

Please provide the full model number of the dishwasher in case you need further help.

Aug 26, 2011 | Whirlpool Gold 24 in. Built-In Dishwasher...

2 Answers

Whirpool dishwasher quiet partner 2 clean light blinking wont cancel or run a cycle


Hello,

press normal heated dryer normal heated dry normal the dishwasher should reset and start. You will need to check the heater this happens because the heater normally fails. Let me know,

http://www.appliancerepairlesson.com/

Mar 07, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

My whirlpool Gold Quiet partner III won't wash. Dishes come out greasy.


Add Jet Dry and run a cycle with dishwasher empty with bleach and should start working good

Nov 19, 2010 | Whirlpool Dishwashers

1 Answer

My 6 year old Whirlpool dishwasher is loud


This is a bad wash pump. Looking at about $175 for just the sump assembly. You could do it yourself, but unit would need to be uninstalled.

May 28, 2010 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Our quiet partner iii dishwasher is not working. It is not gettting dishes cleaned soap left on dishes


Our whirlpool gold quiet partner iii dishwasher is not working well . It is not gettting dishes cleaned soap left on dishes on top primarily

May 16, 2010 | Dishwashers

1 Answer

Dishwasher takes 3 hours to wash, even on the light cycle


whirlpool Quiet partner 3 the clean light is flashing 7 times what does this mean

Mar 12, 2010 | Whirlpool Dishwashers

1 Answer

Whirlpool Quiet Partner V light flashing


most of the time this meens your heat element is burnt out.

Feb 25, 2010 | Whirlpool Gold 24 in. Built-In Dishwasher...

Not finding what you are looking for?
Whirlpool 24 in. DU1100XTP Built-in Dishwasher Logo

1,232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Mike

Level 3 Expert

4340 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...