Question about EliteGroup P4VMM2 Motherboard

1 Answer

Processors WHAT PROCESSORS DOES THIS BOARD SUPPORT?

Posted by on

  • DRTYTRCKZZ Mar 28, 2008

    p4mm2-WHAT PROCESSORS DOES THIS BOARD SUPPORT?

  • DRTYTRCKZZ Mar 31, 2008

    thanx

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,027 Answers

This mainboard has a Socket 478 for the Intel Pentium 4 type of processors supporting front side bus (FSB) speeds up to 400/533 MHz. VERSION 3.2

Also supports HT, hyper threading

Version 1.1-1.3 support only 400FSB pentium 4 socket 478

Posted on Mar 28, 2008

  • Mark Williams
    Mark Williams Mar 28, 2008

    If you have version 1 motherboard than the fastest chip you can put in is
    2.8 Ghz .13 micron 400 FSB Socket 478 512K l2 cache.
    Basically if your version on the board is under version 3 you are limited to .13 or .18 micron 400 FSB Socket 478 from 1.4Ghz-2.8.

    If you have version 3 or higher then it will support HT technology
    and the .65-.90nM. 533 Front Side Bus or the 2.2Ghz - 3.06 Ghz.

    go to this link, filter on selection BUS SPEED 400 for ver 1 533 for version3 package type 478 select filter results.

  • Mark Williams
    Mark Williams Mar 28, 2008

    sorry this link

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Phaser 7400 14: real time clock


According to my service manual, this error is occurring during the Power On Self-Test. While it is a "soft" error, it normally can only be resolved by replacing the Image Processor Board.

But wait! There's more!

Here may be a way to reset without the expensive replacement:
The most likely cause is that the Image Processor Board has not successfully loaded
its NVRAM contents (instructions) into RAM. All print engine operation halts, and
will only become ready when the Image Processor Board successfully boots.
1. Check for media or debris in the paper path.
2. Power cycle the printer.
3. Verifying Image Processor Board failure:
a. Power-off the printer, and remove the Image Processor Board.
b. Power-on the printer. Wait at least 5 minutes while the print engine
initializes. If there was a problem with the Image Processor Board, it will
now not affect the Engine Control Board.
c. If characters appear on the Control Panel display, the Engine Control Board
is functional and the problem is most likely with the Image Processor Board.
d. Turn off the printer and reseat the Image Processor Board and turn on the
printer to determine if seating was the problem.
e. Perform a PostScript NVRAM reset, see "Postscript NVRAM Reset" on
page 6-9.
f. Turn off the printer and systematically remove individual optional
components from the Image Processor Board to isolate a possible problem
component.
g. Replace the Image Processor Board.

I wish you luck with this repair.

Dec 07, 2014 | Xerox Phaser 7400/DX Laser Printer

1 Answer

53mhz system bus processor is installed this processor is not supported on this desktop board and will run at reduced processor clock speed system performance will be impacted intel r pentium iv processor...


Determine the manufacturer and model number of the system board. Locate the system board manufacturer's website. Check for a list of supported processors for your system board. If it is on the list, you may need only to update the system board firmware. If you have questions about the suitability of the processor / system board combination - contact the system board manufacturer's tech support group or technical forums that they may be operating on the site.

Do not attempt to apply a firmware update file to any system board for which it is not intended! Doing so can cause irreparable harm to the system board.

I good luck!

Sep 04, 2012 | Intel Computers & Internet

1 Answer

I need the drivers for compaq processor board 2001-2002


Please give me the Model no your Compaq - Processor Board. The Drivers are avilable in HP Website.

May 17, 2011 | Compaq (169174-001) - (Refurbished)...

1 Answer

Mother board update


Well that can depend on a number of factors like how much you are willing to pay.
Logon to newegg.com or zipzoomfly.com and search through their motherboards for ones that match your processor. pick one that has the features you want. Im partial to Asus boards so id find one of those that would match that processor. They list which processors will work with them so it really is pretty easy. zipzoom is my personal fav.

Mar 09, 2010 | Intel Desktop Board D845BGL Motherboard

2 Answers

Compatible processor 3.0 HT with 845gvsr board


if the processor you have is a pin type one or rather socket 478, yes it will be o.k

Jan 21, 2009 | Intel Motherboard

2 Answers

UPGRADING P 3 PC


THE SE440BX2 MOTHER BOARD CAN SUPPORT P3,P2 PROCESSORS(P3 850 MHZ)....,BUT NOT P4 AND HIGHER VERSIONS...THIS MOTHER BOARD SUPPORTS UPTO 768 MB OF RAM,NOT MORE THAN THIS...

Aug 19, 2008 | Intel Pentium 3 , 450 MHz Pentium III...

1 Answer

Upgrading processor


Do not know much about mac but can you change settings on M/board by using jumpers to upgrade bus speed etc or in BIOS

Aug 13, 2008 | Giga Designs G4, 1.3 GHz (5-1213c)

2 Answers

Plz help me out...problem in assembling AMD Athlon 64 processor in KVM800M board


There is no fix for that. You need a board that is the same as the original because that is the size of the processor. If that is a socket 462 processor, it is only designed and will only run in a motherboard with socket 462 on it. You need to either replace the processor or replace the board with the correct one.

Jul 03, 2008 | Mercury KVM800M Motherboard

3 Answers

Processor upgrade


Need to look at the motherboard specs along with the processor "Socket". It will usually be a 754 or 939 depending on what your motherboard says. I wouldn't try too fast and set yourself up for disappointment. I would upgrade the RAM before the processor.

Mar 22, 2008 | Intel (RK80532PG0881M) Pentium 4, 3 GHz...

Not finding what you are looking for?
EliteGroup P4VMM2 Motherboard Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top EliteGroup Computers & Internet Experts

David
David

Level 3 Expert

778 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Jerry Umali

Level 3 Expert

979 Answers

Are you an EliteGroup Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...