Question about Televison & Video

1 Answer

I have a universal tv sat vcr remote controller that i brought from e bay for about 2 pounds and i need to set it to my bush tv but the instruction manuel does not give me the codes can you help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi in the instructions it should tell you how to do an auto scan to set the right code what you basically have to do is select one of the settings such as tv then you enter the setup mode and keep pressing the standby button until the telly goes off you then store it at that place then that should control your telly from then on,

if your manual does not tell you how to do this then give me the make and model of remote and ill give you step by step instructions on how to do this, the model number maybe under the battery on a sticker give me any numbers on the remote and ill give you the correct instructions on how to do this.

some are philips some are rca so let me know as the setup is different depending on which control it is

here is the instructions for a universal remote check if it works with yours

  1. Step 1 Turn on the component you want to program.
  2. Step 2 Press and release the component button on your remote that corresponds to the component you want the remote to operate (TV, VCR, etc.). The illuminated ON-OFF button will turn on and remain on.
  3. Step 3 Press both the component and the ON-OFF buttons. The illuminated ON-OFF button will turn off, and then will come back on.
  4. Step 4 Release both buttons after the ON-OFF button turns back on. The button should remain illuminated.
  5. Step 5 Press and release the PLAY button. If the component does not respond after five seconds, continue to press the PLAY button every five seconds until the component turns off.
  6. Step 6 Press and release the REVERSE button when the component turns off, then wait to see if the component turns on again.
  7. Step 7 Press and release the STOP button to save the new code.

Tips & Warnings
  • Each time you press the PLAY button in Step 5, the ON-OFF button blinks ten times and a list of 10 codes is sent to your component. This process continues until all of the code lists have been searched. If the component has not turned off after all codes have been searched, the ON-OFF button blinks four times, turns off, and the Auto Code Search is exited.
  • If you do not press the STOP button at the end, the new code will not be saved.
let me know how you get on or if you need further assistance ok

Posted on May 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the code for a Panasonic tv/dvd/vhs combo.....


New 3 digit codes for DVD/VCR, DVR/SAT, TV/VCR, TV ...

www.eliztech.com/remotes/ge-new-3digit-combo-codes.php
DVD/VCR, DVR/SAT, TV/VCR, TV/DVD, DVR/CABLE and DVR/DVD combo codes for GE/Jasco three digit universal remote controls purchased after ... 3 digit codes for GE Universal remotes purchased after August 2002 ... PANASONIC, 437.

[PDF]Manufacture Code List

https://www.att.com/support_media/images/.../set-up-code-list.pdf

AT&TDVD VCR COMBO. VCR. HTIB. REC TUN. AMPLIFIER. TV. Abex 1098. Admiral ....Panasonic 1003, 1010, 1049, 1053, 1096, 1123, 1152, 1231, 1289,. 1292 ...

Remote Control Program Codes - FTC - Farmerstel.com


Jan 01, 2016 | Panasonic Televison & Video

Tip

DISH VIP612 Program AUX Remote Code 2


DISH Solo DVR VIP612 Program AUX Remote Code

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control your receiver, tuner, stereo, second TV or second VCR using your remote's AUX mode? (Instructions to setup a primary TV or a VCR are a little different, but can be found here.)

e818a57.jpg

To setup your Dish Solo DVR VIP 612 Universal Remote, follow these steps to enter the remote control codes to control a device with the AUX mode:

  1. Turn the device you would like to control on.
  2. Find the brand name of the device you would like to control in the control code tables on page 112 of the Dish Solo DVR VIP 612 User Manual.
  3. Press and hold the AUX mode button until all the other buttons light up, and then let go. The AUX mode button will flash.
  4. Press 0 for a TV, 1 for a VCR, or 2 for a receiver, amplifier or tuner.
  5. Enter one of the three-digit codes from the tables in the manual.
  6. Press POUND (#). The mode button will flash three times.
  7. Press POWER to turn off the device. If the device does not turn off, skip to step 9.
  8. Turn the device back on and try some of the other buttons to make sure they work. If the code works, stop here.
  9. If the code didn't work, repeat steps 3 through 7 with the next device code from the tables in the manual.
Your device control codes for your amplifier or other AUX device are now programmed into your DISH Solo DVR ViP 612.

Now you probably want to set your Dish Solo DVR VIP 612 Universal Remote up so that it always controls the volume of your stereo, rather than of your TV, regardless of whether it is in SAT, TV, VCR or AUX mode. Help for this remote control programming can be found here.

(Help for programming a TV or VCR using the TV or VCR mode buttons can be found here.)

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | Televison & Video

2 Answers

Need code for magnavox tv urc-4021boo


Hi, the codes you have requested;

Magnavox - 0054, 0706, 0030, 1454, 1254

Instructions to program code:

1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc). NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.

2. On the remote control,press a device key once (i.e., VCR/PVR, DVD, CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press VCR/PVR once.After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions. NOTE: To program control of a DVD Player,DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD once.After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions. NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,then release SET.

4. Use the Manufacturer's Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

5. Aim the remote control at the device and press POWER once.The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works.

Feb 12, 2011 | One For All URC-4021 Remote Control

2 Answers

We just got a new Dish HD/DVR Receiver and need the remote code for the Bose remote control to operate it.


Here is what I did for my Bose Solo Tv to work on the Bell 9242 receiver.( see page 17 of Bell 9242 guide) 1. Hold down the aux button until all lights flash. 2. Press 2 to ensure Aux is set to audio. 3.Enter code 761 and press the pound (#) button. Now to have the satellite remote default volume to Bose Solo do the following. 1.Press and hold AUX 2.press # pound 3. Press the + side of volume 4. Press 0 5. Press pound ( AUX button will flash 3 times) 6. Press SAT mode 7. Test the volume on Bose Solo. (see page 22 of Bell 9242 guide)

Jul 05, 2010 | Bose 3 2 1 GSX System

1 Answer

WHATS THE CODE FOR RCA TV ..I HAVE A ONE FOR ALL UNIVERSAL REMOTE NEED THE CODES TO PROGRAM MY RCA TV


You received a list of ALL Codes with your universal.

I got this off the internet. But I do not know what type of universal you bought. You didn't mention it.
Good Luck.
Here is the link if you need it. :0)

http://www.google.com/search?q=universal+code+for+rca+tv&rls=com.microsoft:en-us:IE-SearchBox&ie=UTF-8&oe=UTF-8&sourceid=ie7&rlz=1I7GGLL_en

rca

Nov 07, 2009 | Universal Remote Control P000203220-1...

17 Answers

Programming a URC22B universal remote controller


QUICK SEARCH
Turn device on
Press and hold [SET] button, then press and release DEVICE button eg tv, vcr , sat, aux
release [set] point the remote at device and pres [POWER] or [PLAY]
until device turns off or plays
Press [ DEVICE] to lock up the code
check other buttons

Nov 17, 2007 | Jensen JR500 Remote Control

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74383 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...