What does ER-5 mean? - Audio Players & Recorders

ER just means error, so it could be anything. Disconnecting from the mains for 5 minutes is often a form of reset.

YOU did NOT SPECIFY your MODEL NUMBER but tonight ~ Christmas Eve ~ YOU got LUCKY! I found this and it may help you... but
THIS INFORMATION MAY NOT BE FOR YOUR DEVICE!

"LCD shows "Er 4"
Pneumatic system leak
or cuff is too loose during inflation

And this:

LCD shows "Er 0"
Pressure system is instable before measurement
Be still and measure again

LCD shows "Er 1"
Systolic pressure detect fail

LCD shows Er2 Diastolic pressure detect fail

LCD shows "Er 3"
Pneumatic system is
blocked or cuff is too
tight during inflation
Place the cuff correctly
and try again

LCD shows "Er 4"
Pneumatic system leak
or cuff is too loose du-
ring inflation

LCD shows "Er 5"
Inflation
above
300mmHg
Measure again after 5
minutes. If the moni-
tor is still abnormal,
please contact the
local distributor / ma-
nufacturer.

LCD shows "Er 6"
Over 3 minutes while
pressure above 15
mmHg

LCD shows "Er7"
EEPROM accessing er-
ror

LCD twinkling
Device
parameter
check error

LCD shows "Er 9"
MCU self-verity error

LCD shows "Er A"
Span error

LCD shows "Er b"
EEPROM Backup-error


http://webcache.googleusercontent.com/search?q=cache:V0KPe0jswmgJ:www.hmm.info/uploads/tx_sbdownloader/smartLAB_profi_user_manual_ENGLISCH_R4.pdf+&cd=2&hl=en&ct=clnk&gl=us&client=firefox-b-1

Motor Wiring Trip
The motor has a short circuit to a battery connection. Check all the connections and leads between the motor and the battery.

Does it just show "er" or does it have "er" and two more characters? The "er" means there is some sort of problem, and the other two characters will indicate what kind of problem. If it's just showing "er" alone, I not sure what that means.

ER means error. Normally ER follows with concerned number.

We don't understand what you exactly mean. If it means a eror code, please find below the error codes and its solutions.
Er FS - Freezer Sensor Error
Er rS - Refrigerator Sensor Error
Er ds - Defrost Sensor Error
Er dH - Defrost Heater Error
Er CF - Cooling Motor Error
Er CO - Communications Error Er-Ff- Freezer fan fault. Write again if you're not satisfied with this answer.Thanks.

ER in temp means error code next 2 letters are first letter of part giving problem or where problem located.. if " ER DH" means def heater not coming on, does not mean heater bad but def control bad not letting voltage to heater. could need main bd also

Sounds like it wasn't initialized, even though it says Er 4 instead of Er 0... According to my manual, to (re)initialize it and reset it to zero, tap the platform lightly. It should show zeroes running across the display for a second or two, then show all zeroes and turn off. It should be re-initialized...

Error Codes for the 5757 (according to my manual):

Er 0 Initialization error (remedy described above)

Er 1 Instability error (step off the scale, then back on)

Er 2 Overload warning (registering weight beyond the 440 pound max)

Er 3 Contact error (body impedance beyond technical limit - try dampening feet and try again for better contact)

Er 4 Bodyfat error (bodyfat percentage is beyond range - try dampening feet and try again for better contact)

Er 5 Bodywater error (bodywater percentage is beyond range - try dampening feet and try again for better contact)

er ff means that the control board is not sensing evap fan motor operation this means either a bad fan motor ice in the fan motor or bad control board. you can verify fan operation by opening freezer door and feeling for old air blowing from back of freezer compartment. you will have to push in the light switch to get fan operation.
for corndo that has same problem you actually have a different problem. er dh means the control board is not sensing defrost heater operation. the most common culprit is a bad defrost sensor. message me back if you need instructions for trouble shooting..thx peyton

Hello que1995
Welcome to Fixya,

You said, Message on front panel is "ER IF". We do not have manual. Any idea what that means and what we need to do?

While I look it up, you can try to reset the system by plugging the fridge for 5 minutes, or if you can not reach the plug, then throw the breaker for 5 minutes.
Not less than 3 minutes. That is why I sad, 5minutes.
Usually this will do it! let me know as I look up the error codes.

Let me know that it works
Please remember to leave a rating!!!!!

Thank You Huuum