Question about Washing Machines

1 Answer

Bosch washer/dryer I have a Bosch Excell washer/dryer, model 24520GB. When washing the fault display F:17 appears, which I think in my situation means low water pressure, but it works. However, in the Dryer mode, after about a minute the dryer stops and the F:17 fault displays. How can I get the dryer to operate?

Posted by on

  • coolbeatph Oct 15, 2008

    i really have d same problem.


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I also have the same washer and same problem, and it is not due to clogged filters nor due to low pressure!

Any solutions so far?

I wish I had read these posts before buying it. :(

Posted on Nov 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does error F:16 indicate?


no one will know without a MAKE and MODEL.

Dec 26, 2015 | Washing Machines

1 Answer

Bosch Nexxt 100 series washer stops at 1st spin cycle


take a look at your manual that came with your machine go to problems usually at the back and see what that says,or go to the bosch website and type in your model number its on the inside of the door.i would suspect a program fault.adrian,,,,,

Jun 28, 2010 | Bosch Nexxt 100 Series WFMC1001UC Front...

1 Answer

What does F02 fault mean?


Hello elaineginolf, welcome to Fixya. Error code "02" typically indicates a lock problem. Since not all models are the same can you clarify the model of Bosch you have ? The post category says WFL2060 but that can't be since that model has no display and faults are indicated by way of led lights flashing in a set pattern. Could it be a WFR2460 with the digital LED display ? Let me know and I'll see if I can assist you from there. Macmarkus :)

Jun 26, 2010 | Bosch Axxis WFL 2060 Front Load Washer

2 Answers

Bosch Excell washing machine programme fault


This video will show you how to replace the Bosch washing machine heating element and thermostat with step by step guide on the process

Jun 28, 2009 | Bosch Washing Machines

1 Answer

My manual for bosch washer dryer wft6 is in norwegian and display lights flashing as fault but cannot understand it


you can now download the manual for this appliance direct from the bosch web site if its not listed there try the bsh home appliance web site when you connect it will ask you what language you want the manual in
good luck

Mar 10, 2009 | Bosch Logixx WFT 2806 Front Load...

1 Answer

Boschh Exxcel washing maching 0 Fault F16 displayed


F16 on a Bosch indicates the door is open / unlocked.
If it's happening during a wash it would suggest either a faulty door lock, faulty wiring or worse, a faulty main control board.

The wash programme should halt when this comes up but you should be able to restart it when the door is closed.

As the cost of a new door interlock isn't overly expensive I would suggest fitting a new lock on a "fit and see what happens" basis.

Hope this helps
Thanks

Apr 25, 2008 | Bosch Exxcel WVT3250 Front Load Washer /...

1 Answer

Tumble dryer not working


I managed to solve the problem the following way: I noticed that if you unplug the Sensor-NTC(part nimber 154431 https://www.bosch-eshop.com/eshop(bD1lbiZjPTAwOQ==)/bosch/gb/prodp.htm?prod=WET2820GB%2f13 ) that controls temperature of air in the air channel, the drying cycle runs as you describe above. So this circute was checked up to the power module. Contacts of the Sensors plug were tightened; I think this solved the problem; resistance of the sensor checked. It must be 4.8K at 25 degree C. and decrease when temperature increases. I dipped the sensor in a glass with hot water. 

Oct 25, 2007 | Bosch WET 2820 Front Load Washer / Dryer

2 Answers

BOSCH 1400 excell


find the punch hole on plate use pointed object stick in hole and turn

Oct 05, 2007 | Bosch WFMC 3200 Front Load Washer

1 Answer

Fault code 01


this is actually a fault code error code 1 not one minute check your manual as codes different on some machines from memory i think 1 is a filling fault this machine uses fuzzy logic if water fill takes longer than 4 mins (low pressure) machine stops can be restarted by pressing start button.
see if machine will complete just a rinse cycle.

good luck

Oct 04, 2007 | Bosch WFE 2021 Front Load All-in-One...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...