Question about Kyocera CS-2550 Black and White Copier

2 Answers

Scanner - memory is full

Scan 60 pages and scanner states memory is full... how do I correct this problem... In the pass I have ran more than a 1000 copies before this notice would pop up...

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

In comant senture u can make the scan megabyte more

Posted on Aug 07, 2012

  • Louis Du Plessis
    Louis Du Plessis Aug 07, 2012

    in comant senture u can make the scan megabyte more

×

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

A KM-2550 has 64 MB RAM built in. I believe less than 30 of it is for image storage. You may be able to lower your scan resolution. 
Best solution is to add more memory. Look for a Kyocera compatible 100 pin dimm (don't buy from the manufacturer). It will read 16 MB to 256 MB sticks. You have to take out 6-8 screws holding on the part of the back the sticks out on the upper left. Make sure after installing you print a status page to make sure the memory was recognized.

Posted on Apr 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Colored lines on a copy page


To fix the colored lines on a copy page do the below steps

  1. Disconnect the power cord, wait five seconds, and then plug it back in. This will reinitialize the unit and force the scanner to calibrate again.
  2. Examine the scanner glass and white scan backing. Clean the scanner glass and scan backing if they are not clean. To clean the scanner glass and scan backing, use a soft cloth towel slightly dampened with clean water.
  3. With the product turned on, open the scanner cover and check the bulb assembly. If the scanner bulb is not lit, the unit must be serviced.
  4. Verify that the alignment page is placed on the scanner glass or in the automatic document feeder (if equipped) correctly. Place the printed side down.
  5. Make a copy of the alignment page. The unit will make a copy even if the alignment message is displayed. Compare the copy to the original. If vertical lines appear in the copy, check to see if the scanner assembly requires cleaning. If cleaning the scanner assembly does not correct the problem, service the product.

Dec 10, 2010 | HP OfficeJet k60 All-In-One InkJet Printer

1 Answer

When i press the scan button , nothing happens at all ,, please help i need to scan photos


The scan button requires proper setting of the program on the computer that tracks the state of that button.
Reinstall drivers (full installation).
Why not open My Computer, find the icon of the scanner and scan using Microsoft scanner or camera wizard?
You can also open MS Paint and scan using File / From scanner or camera.


Aug 09, 2010 | Office Equipment & Supplies

2 Answers

Brother MFC-7820N Printer--vertical lines


You need to clean the scanner glass. Also known as the strip glass. It is a 1 inch wide strip of glass that runs from the front to the back. Your documents pass over this glass when they are scanned. Some of the wax crayon probably smeared off onto the glass and now when you scan the scanner sees these marks as stationary and thus records them as solid lines. Just look into the scanner section where your documents are fed in or depending on model, some are just to the left of the large original glass.
Good Luck and thank you for using Fixya.

Feb 25, 2010 | Brother MFC-7820N Printer

1 Answer

Insstructions for sending a Fax on a Brother


You can find the entire user manual by clicking here:
http://www.brother-usa.com/ModelDocuments/Consumer/Users%20Manual/UM_MFC_240C_EN_249.PDF

Or, here are the instructions for sending a fax:

Entering Fax mode 5

To enter fax mode, press (Fax), and
the key will glow green.

The LCD will show the new job number and
the memory available.The number of pages
you can scan into the memory will vary
depending on the data that is printed on them.

Faxing from the ADF 5
a Make sure you are in Fax mode .
b Put the document face down in the ADF.
c Dial the fax number using the dial pad.
d Press Black Start or Color Start.
The machine starts scanning the
document.

Note
• To cancel, press Stop/Exit.
• If the memory is full, the fax will be sent in
real time.

Faxing from the scanner glass5
You can use the scanner glass to fax pages
of a book one at a time. The documents can
be up to letter or A4 size.

You cannot send multiple pages for color
faxes.



Make sure you are in Fax mode .

Load your document on the scanner
glass.

Dial the fax number.

Press Black Start or Color Start.
If you press Black Start, the
machine starts scanning the first
page. Go to step e.

If you press Color Start, the
machine starts sending the
document.

Do one of the following:
To send a single page, press 2 to
choose No. (or press Black Start
again).
To send more than one page, press
1 to choose Yes and go to step f.

Put the next page on the scanner glass.

Press OK.
starts scanning the page.

.

Dec 15, 2009 | Brother MFC 240C All-In-One InkJet Printer

1 Answer

When I copy or scan a picture a line is down the center of the picture


When scanning the page it is passed over the scanner, a mark on the scanner will then be copied down the full lenght of the page. I not sure how much access to the scanner you have with this model but you need to examine the scanner for a spot of dirt/correction fluid and clean it, you may need to scratch it off with an old credit card or similar

Sep 09, 2009 | HP OfficeJet k60 All-In-One InkJet Printer

1 Answer

How do you get a scanner to scan a full document not only a piece of it?


In a large number of scanners on the first pass it will offer a preview option. When it shows the thumbnail view you can drag an outline of what it thinks you want to scan out to cover the full page. Also you will sometimes have to tell it what size paper it is looking at from a small picture to a legal page. Check the scan settings and see if this info helps. Good Luck

Jul 21, 2009 | Canon MultiPASS MP730 All-In-One InkJet...

1 Answer

Scanning limited to 11 pages


You must have your scanner resolution set way up

Mar 13, 2009 | Muratec Office Equipment & Supplies

1 Answer

When scanning, the scanned page is not readable from a third of the page down to two thirds of the page.


It is important that the item you scan comes in close contact with the scanner glass. If the resulting scanned image is not clear, check to see that the item is in full contact with the scanner glass. The scanner uses optical character recognition (OCR) to convert text on a page to text that you can edit on your computer.
  • If you scan text but cannot edit it, make sure that you make the following selections during scanning:
  • Scanned text might not appear on your computer exactly as it appeared on the original, especially if the original contains faint or smudged text. For example, some characters might be incorrect or missing. As you edit the text, compare the scanned text against the original, and then make corrections as necessary.
  • To change text scanning options, click the Scan Document Settings button in the initial What are you scanning? screen.
  • The OCR software is installed by default when you install the HP Scanning software during scanner setup. If you use the Custom option when installing the software, you can choose not to install the OCR software. Try reinstalling the software using the default install options.
  • Email to jdiaz@coretec.us
  • If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
    Thanks, Joe

Nov 07, 2008 | HP Office Equipment & Supplies

2 Answers

Pixma mp600r scanning setup


Try turning off the windows firewall.
If that works, then add the Canon scanner app to the list of applications that are allowed through the firewall, then turn the firewall back on again.

Jan 24, 2008 | Canon PIXMA MP600 all-In-One InkJet...

Not finding what you are looking for?
Kyocera CS-2550 Black and White Copier Logo

Related Topics:

1,522 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

NewYork kyocera HP...

Level 3 Expert

513 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Tech Bravo
Tech Bravo

Level 2 Expert

337 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...