Question about GPS Devices

3 Answers

Need to update Furuno 1833C (2002) NavNet mini chip for updating map.

Posted by on

  • cmorgjr Mar 27, 2008

    USA, Gulf of Mexico, Panhandle

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi what map do you need to update what country are you in

Posted on Mar 27, 2008

  • paul proctor Mar 27, 2008

    click here try this link see if it has what you need then get back to me

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

HI,

Can you please give more details about your problem.If you need the manual you can download it from HERE

Goodluck,
Please don't forget to rate the solution.

Posted on Mar 27, 2008

  • Priya darshan Mar 27, 2008

    I've got some more details regarding the update thing.You can check that out from HERE

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 19,396 Answers

You need to download the firmware, I will see if I find the download online.

Posted on Mar 27, 2008

  • 1 more comment 
  • Ginko
    Ginko Mar 27, 2008

    There are two kinds of updates you can do on your Furuno:

    1) If you need to do software update do the following:






    Refer to your Operator's manual and perform the SELF TEST on your unit.
    This will provide you with the program number of the software on your
    unit. You will need this information when you contact your local,
    authorized Furuno dealer who can assist you with determining if you
    need to update your software.

    If
    you are experiencing difficulty with a piece of equipment, often your
    best course of action is to have an authorized Furuno dealer inspect
    the unit. Most problems with new units can be easily traced to
    installation, initialization or set-up issues. Older units usually are
    more susceptible to physical wear and tear, rather than a software
    problem.

    Here is " Dealer Locator" on Furuno website for (Link is for USA). This will allow you to search for dealers in your area by zip code.
    Here is link to Furuno Global if you live in a different country.

    If you need to download a new map or update your map you need to give us your locatiom and tthe location of maps that you need

    Here you get charts cards from Furuno

    Here you can ask your question straight to Furuno

    Hope it helped.

    Regards

  • Ginko
    Ginko Mar 27, 2008

    Then here are charts cards from Furuno Follow instructions to load charts HERE.
    If you need to update software follow instructions above.
    Furuno USA is furunousa.com.

  • Ginko
    Ginko Mar 27, 2008

    You can post a request for maps on this forum. If you are lucky you will get maps for a small fee or for free from some other user.
    Here is the link to noe seller on ebay.

    If you cannot find anything else, here comes the address for a Furuno dealer in FL, use Dealer Locator to find more:




    Tropica Boats & Marine, Inc.



    4841 Waycross Road
    Ft Myers, Florida 33905




    Telephone :
    239 694-5259



    Fax :
    239-694-5243









×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the "toolbar" from the top of the screen on my furuno NavNet Vx2?


go to toolbar with controller, and push clear key. just it.. but when you restart your system, it appears again. if you wanna lose it anytime, you must do it inside the General Setup.

thanks..

Dec 21, 2012 | Furuno NavNet vx2 1920C GPS Receiver

3 Answers

Ais and 1920c Furuno chart plotter


n the system setup, under “UNITS” I set BEARING to “MAG” (magnetic). This will cause the unit to display course / bearing information in relation to the Magnetic North and match magnetic compass readings. It is not the same as True North! One has to be careful with this setting. There are a number of areas where the earth's magnetic field is locally disturbed, sometimes very significantly. Your GPS may not account for it. - again, under “UNITS” I set “METRIC”.

Sep 02, 2008 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

I have a Furuno Radome RSB0094-075 with a Navnet RDP 139 10.4" What I dont have is the antenna cable to connect the two units. What cable should i be ordering for this?? Thanks, Mike


That is a Furuno 1823C Radar -000-138-972 (10 meter Radar cable) $150.00 msrp from Furuno. Give their Camas Office a call or your nearest dealership. The Furuno number in Camas, Wa 888-834-9330

Nov 06, 2010 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

How to interface a furuno 1833c navnet to a usb port and how to download waypoints to my pc.I have the older 9 pin pc cable and a usb adapter cable.Looking for usb drivers and software to make it work.


The display uses a serial interface, otherwise known as a comm port. You can get a USB to DB9 adaptor practically anywhere. Once you have a serial connection, you will need software such as MaxSea to send the waypoint with.

Jan 11, 2010 | Furuno 1833C/NT GPS Receiver

1 Answer

GP1920C & BBWX1 SIRIUS WEATHER


You need to convert your Navnet to C-map. You can not run both on the same unit. Mid-Shore Electronics can help you out with this. Check out their website in the tech corner.

Jun 05, 2009 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

Radar install problem


the GP31 has an NMEA in/out in the power cord - out is yellow green in blue(or black) and white on the 1833 you will use data 4 typically which has an in and out also, same colors hook out to in and in to out, program and done

Mar 23, 2009 | Furuno 1833C/NT GPS Receiver

1 Answer

Adapt 997c si gps to navnet furuno sounder


no can do you must have a Furuno GPS or a GPS with NMEA 0183 output. you could get that from the Hummingbird display but not straight from the antenna

Feb 27, 2009 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

Furuno 1833C/Dgps37 Plotter creeps


Try adjusting the GPS position offset in the GPS Sensor Settings Menu.

Jan 11, 2009 | Furuno 1833C/NT GPS Receiver

1 Answer

Furuno Radar Model 1833C


You have two things that orient the radar, on is called heading (or bearing) alignment. This is where you aim your radar so that a target comes up at 12 o'clock when dead ahead. Access this mode by pressing and holding menu duing power on, and go in to Installation Mode, radar setup, next page, align heading. I have posted a "tip" on this, search for VX2 radar alignment.
After this is done, North up is accomplished by having a magnetic input (fluxgate compass or autopilot). Calibration of this compass varies, but if it is accurate, then all should line up nicely.

Jul 03, 2008 | Furuno NavNet vx2 1920C GPS Receiver

Not finding what you are looking for?
GPS Devices Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top GPS Devices Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

k24674

Level 3 Expert

7987 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

Are you a GPS Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...