Question about Dishwashers

1 Answer

No heating in dishwasher

Dx302 model running whole cycle but not heating or drying

Posted by on

  • 1 more comment 
  • Anonymous Apr 30, 2008

    where is the solenoid

  • Anonymous Feb 15, 2009

    my dishwasher wont heat the water or dry the load

  • Paul VS Apr 25, 2009

    no heating in dishwasher

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Repair the solenoid

Posted on Mar 27, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset Kenmore Elite 665-16572202 Dishwasher...clean light blinks 7 times pauses then repeats. My model does not have a Heated Dry button it has an Air Dry button.


Here's the key sequence(s) to use, depending on how your keys are labeled:
Heated Dry - Normal - Heated Dry - Normal; or
High Temp - Air Dry - High Temp - Air Dry; or
Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry; or
High Temp Wash, Heated Dry, High Temp Wash, Heated Dry.

This will start the diagnostic cycle. Let the dishwasher run for a few minutes, and then press Cancel to stop the dioagnostic cycle and clear the error. Please note, that this clears the error, but if you haven't found the cause (water-not-heating error), the condition will come right back the next time you run the dishwasher.

Jan 19, 2015 | Kenmore Dishwashers

1 Answer

Dishlex dx302 not drying dishes. Doesn't seem to be as hot as usual when opened immediately after finished. Steam not present.



Hi,
Check your heating element..


A bad heating element causes many problems in dishwashers...

Dishwasher Problems The
Heating Element not Working


How to Replace the Dishwasher Heating Element


Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes

Mar 04, 2011 | Dishwashers

1 Answer

Electrolux dishwasher DX302 isn't drying the dishes. What might be wrong?


Hi,
Check your heating element..
A bad heating element causes many problems in dishwashers…

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes


Aug 27, 2010 | Dishwashers

2 Answers

User manual for electrolux dishlex DX302


Go to http://www.dishlex.com.au/SupportCentre and then search by the model description DX302WB. I downloaded a pdf file no problem.

Nov 12, 2009 | Electrolux Dishwashers

1 Answer

Dishwasher cycle runs: tablet is not dissovlved, dishes dirty


If the dry cycle has a problem, check these:

Heating element
Drying fan
Thermostat
Heating element Your dishwasher has an electrical heating element that helps to dry the dishes. If the element is burned out, the dishes won't dry properly, and you need to replace the element.

Drying fan Many high-priced dishwashers have a small fan that blows air or heated air into the dishwasher to speed up the drying process. If the fan is defective, you need to replace it.

Thermostat Some dishwashers have a thermostat that monitors the drying temperature. If the thermostat is defective, the heating element may not cycle on or off properly. If that's the problem, you need to replace the thermostat.

Aug 29, 2009 | Frigidaire Dishwashers

1 Answer

Ge dishwasher not drying


1 make sure heated dry is on.
2 run your cycle and when it says drying open the dishwasher. see if it has steam coming out.
3 give me your whole model number.
4. if heater is not turning on then you may have one of three issues.
1. Bad door switch
2. Wire off element or bad thermistat
3. No power going through the control. to the heating circuit.

Jan 07, 2009 | GE ADW1100N Built-in Dishwasher

2 Answers

No heating in dishwasher


Do not plug it into hot water UNPLUG. It needs cold water going through the system.

It may be the heating element or just a loose connection on the computer panel.

If you have any Questions plese do not hesitate to ask

Dec 03, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...