Question about Baby Gear

1 Answer

HOW RE-ASSEMBLE A GRACO CAR SEAT - Baby Gear

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,049 Answers

1) If your child is under 35lbs get the locking clip that came with the seat if you have a seat with a shoulder harness attached. Otherwise, it isn't necessary. Pull the shoulder harness down to the base of the waste strap and then use the locking clip to bind it into place.

2) For a smaller child you will need to install the built in straps like so.
HOW RE-ASSEMBLE A GRACO CAR - 2cfccec.jpg
27244bb.jpg

3. Set the seat in place running the waist strap through the back of the seat and clipping it on the other side.

LARGER KIDS: If the child is over 35lbs, use the belt and shoulder harness as you would an adult and simply extend the belt over the seat. You do not need to install the built in straps.

Posted on May 06, 2010

  • NA NA
    NA NA May 06, 2010

    Diagram for using seat without built-in Harness.




  • NA NA
    NA NA May 07, 2010

    Was this helpful?

×

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
busboy2
  • 50 Answers

SOURCE: graco car seat

cant help you you need to take the seat to a dealer to show you how for safty reasons

Posted on Mar 16, 2008

robotek
  • 1512 Answers

SOURCE: Need to Re-Assemble my Graco Snug Ride Car Seat

Hi jessibee


I found the site that you need to get an instruction manual for the seat. You will need to find the exact model of the SnugSeat that you have, because there are quite a few to choose from.

to find the model/serial number...

Car Seat trans.gif Toddler or Booster - On the back of the car seat OR on the bottom of the seat

Infant - On the back of carrier OR on the bottom of carrier OR on the stay-in-car base




Thanks for using FixYa, a Fixya rating would be great for this advice.

Good luck.

regards
robotek

Posted on May 09, 2008

  • 11 Answers

SOURCE: Graco Car Seat (French Roast) lost manual

Try the product's website, try this website http://www.manualsonline.com/, and if those two aren't a help try different search engines.

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions for graco junior mini car seat


http://www.graco.fr/pdf/8H98%20MODEL%20GB%20FR%20NL.pdf

I found the instructions on the french graco site. Hope this helps anyone else looking through for this old car seat.

Apr 09, 2012 | Graco Baby Gear

1 Answer

I washed my daughters graco car seat and now i havent a clue of how to put it back together and i need re assemble it fast please help


Proper installation of a car seat is imperative to protectan infant. Accidents do happen and assuring that the instructions forinstallation of the Graco Infant Restraint/Carrier are followed will increasethe chances of preventing injury or death as a result of an accident. Graco carseats are a popular choice among parents due the availability of products atcommon retail stores, affordability and user-friendly baby gear.Graco Car SeatInstallation
Step 1
Plan to secure the infant seat facing the rear inthe middle of the back seat. If a center position is not available, positionthe seat directly behind the driver's side seat. For safety reasons, therestraint should not be placed in a position where there is an air bag. Ensurethat the proper vehicle lap belt system is in place; manually adjusted lapbelts, automatic locking retractor lap belts and lap/shoulder belts withlocking latch plates are all considered safe for use with the Graco InfantCarrier/Restraint.Step 2
Remove the carrier from the Graco car seat baseby squeezing the lever at the rear of the restraint and lifting the seat up.Place the base in the vehicle facing the rear. Thread the vehicle shoulder andlap belts through openings at the end of the base without twisting the belts.Secure the belts by placing plastic tongue over the belts. Tighten the vehiclebelts by pushing down on the base and pulling out any slack.Step 3Install locking clip to secure shoulder and lapbelt together just above the seat belt buckle. Connect the two belts with thelocking clip. Buckle the lap belt system and tighten by pulling out any slack.Ensure that car seat base is secure by pulling and pushing on it; the baseshould not move sideways, forward or backward.Step 4
Place the Graco carrier in the base. Push down onthe restraint until it clicks and locks into the base. Set the infant in therestraint for travel and place harness straps over the baby's shoulders. Clickthe chest place together over the sternum and lock the buckles into placebetween the legs.Tipsand Warnings
  • Contact local police departments, hospitals and fire departments to inquire about child car seat safety checks
  • Graco Infant Restraint/Carrier will not protect against serious injury or death if not installed properly. Always read the Graco owner's manual that comes with product prior to attempting installation and travel with an infant.

Jul 19, 2011 | Home

1 Answer

Do we have to use the graco car seat fixing base in the car as it doesnt actually fit behind my seats and couldnt we just use the actual car seat on its own as long as it is held in with a seat belt etc,is...


You can use the base or just use the car's seat belts to hold the car seat in place. Make sure it is tight. Download the instructions from Graco or it should be on the side of the car seat on a sticker.

May 04, 2010 | Graco Snugride - Family Tree Infant Car...

1 Answer

Graco Car Seat (French Roast) lost manual


Try the product's website, try this website http://www.manualsonline.com/, and if those two aren't a help try different search engines.

Aug 04, 2009 | Graco SafeSeat Infant Car Seat - French...

1 Answer

Need replacement level indicator for graco giselle infant seat


go to www.gracobaby.com and type in your model number and serial number (or date of manufactor, and it will bring up all the available replacement parts for your seat.

Mar 21, 2009 | Graco SnugRide - Giselle Infant Car Seat

1 Answer

Is this stroller compatible with other car seats such as Graco?


The manufacturer will not say that your Graco seat will fit in their stroller safely, however you could try your Graco in it and see if you feel safe that it will not fall out or be pulled out by your toddler.
Perego prefers to market their items to go with their car seats only, but we have found that the Graco seats fit nicely in most strollers. You should hook the stroller harness on to the lap belt routing path on your car seat to ensure safest travel in the stroller.

Good Luck! from Moms Just Know

Oct 02, 2008 | Peg Perego Tender XL- Black Sable Twin...

1 Answer

Need to Re-Assemble my Graco Snug Ride Car Seat


Hi jessibee


I found the site that you need to get an instruction manual for the seat. You will need to find the exact model of the SnugSeat that you have, because there are quite a few to choose from.

to find the model/serial number...

Car Seat trans.gif Toddler or Booster - On the back of the car seat OR on the bottom of the seat

Infant - On the back of carrier OR on the bottom of carrier OR on the stay-in-car base




Thanks for using FixYa, a Fixya rating would be great for this advice.

Good luck.

regards
robotek

May 09, 2008 | Baby Gear

1 Answer

Graco car seat


cant help you you need to take the seat to a dealer to show you how for safty reasons

Mar 15, 2008 | Graco SnugRide - Giselle Infant Car Seat

2 Answers

Valco Tri Mode Stroller - car seat adaptor


the car seat goes in so that the baby is facing you if you are pushing. the bar on the adapter goes into the two plastic pieces sticking out of the back of the car seat. the red hook in the graco seat will latch on. it is confusing because the baby is seemingly far from the person pushing.

Mar 02, 2008 | Valco Runabout Tri Mode Jogger

Not finding what you are looking for?
Baby Gear Logo

Related Topics:

1,252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baby Gear Experts

Dorel UK
Dorel UK

Level 3 Expert

1629 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Baby Gear Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...