Question about Optoma H30 Multimedia Projector

1 Answer

Replaced bulb but still getting "lamp will fail soon replace" warning

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

When you replace the lamp, you need to reset the lamp counter as well. The procedure for this should be in the owner's manual. This counter is a guide only. Lamps have an expected lifetime and the message indicates that the lamp is nearing that lifetime. Once reset, the counter will again trigger the message once this new lamp reaches that usage time.

Dan

Posted on May 06, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Replace lamp soon flashing during warm-up

Press the left and right buttons, as well as the power button once the lamp has turned on. This will reset the lamp life counter.

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed the bulb but it keeps saying replace bulb


Look through the settings to see if there is a reset option for warnings or for lamp warnings. Many products with lamps require you to not only replace the lamp but to reset the warning.

Oct 18, 2012 | Ecoquest Fresh Air Air Purifier

1 Answer

2012 cbr 1000 check engine light 2 slow 3 fsst


warning lamp some used for warn low oil pressure, etc.
Wtith the bulbs use for most warning light circuit it is hard to determine whether or not the filamente is good. Will be a good idea to replace the bulb.
For test the faulty warning lamp, turn the ignition switch to START, this light the warning lamp. I f the light does not come on , disconnect the sender switch lead. . Use a jumper wier to connect the sender witch lead to ground. With the ignition in RUN the warning lamp should light. If the lamp is illuminated replace the sending switch. If the light does not come on,either the bulb is burned our or the wiring is damaged.Use test light for confirm voltage is present at the sensor terminal connector. If there the bulb is bad.
God bless you

Oct 05, 2012 | Cars & Trucks

1 Answer

I have a panasonic projection TV, PT-60C13 that will not turn on. Upon pressing the power on button, the button flashes green many times, then flashes red five time then one orange flash. This red/orange...


Hi,

The most common cause of Panasonic Rear Projection LCD TVs not starting is bulb failure. The PT-60LC13 users manual gives some help in translating the LEDs on the front of the TV.

If the TV worked normally for a period of time (months or years) and won't start, the most likely cause is bulb failure. There is no way to measure the bulb, sometimes the bulb is visibly damaged when it fails. Remove the Lamp Assembly and look at the bulb.

If there was an On-Screen Lamp Replace warning and TV won't start, bulb has failed.

The first step with all Panasonic Rear Projection TV "No Picture" problems is bulb replacement. If that does not remedy the problem, get a technician, there are no user serviceable parts. Guessing if the ballast, power supply, controller board or optical engine is faulty is not practical.

The Panasonic Lamp Gallery shows all Panasonic models and Lamp Numbers. There is also a link to Panasonic DIY bulb and lamp replacement.

easyab

May 05, 2011 | Panasonic PT-60LC13 60" Rear Projection...

2 Answers

I have panasonic pt52lcx65 it kept saying to replace bulb now the screen wont come on does that mean the bulb went complety out?


Howdy,
YES, the TV was telling/warning you that Lamp was going out soon so you would not be without the use of your TV while you get a Lamp.

Thanks for using FIXYA, BIG IRISH.

Nov 14, 2009 | Panasonic PT-52LCX65 44" HDTV

3 Answers

Infocus IN24 lamp not lighting up


MAKE SURE BLUB WIRING IS THE SAME AS OLD BLUB, IN24 AND IN24+ WIRING IS DIFFERENT IN CONNECTOR.

Mar 20, 2009 | InFocus Projector Lamp for IN24+, IN26+

1 Answer

Replace lamp soon flashing during warm-up


Press the left and right buttons, as well as the power button once the lamp has turned on. This will reset the lamp life counter.

Jan 16, 2009 | Mitsubishi XL5U ColorView Multimedia...

1 Answer

How to reset lamp meter


I have a PT-50LCX63 unit. After 5 years and 4 bulbs, a "reset lamp" warning showed up every time I turned on the tv. I have to say that after a few weeks, the message ceased on its own. I don't know if all models eventually reset or turn off, but I could not find any other information on the direct way of resetting. I find the warning a waste of time since the bulbs are good for 10 -14 months. Sadly I missed the class action suit that dealt with the premature lamp failures. I am looking for a new tv at this point. Bulbs have cost me $1200.00 since I bought it. The warning is supposed to allow you the option of replacing the lamp before it fails, Ha! what a joke...Thanks for reading.

Dec 29, 2008 | Panasonic PT-50LCX63 50" Rear Projection...

3 Answers

Optima H30 warning


OK, found the solution on the net, you have to use the buttons on the projector instead of the remote to access the menu item.

Aug 25, 2008 | Optoma H30 Multimedia Projector

1 Answer

Brightness Varying during operation


Inside all projectors is a lamp ballast that runs the lamp. It could be in the early process of failing.
This website will explain the whole ballast thing clearly. It is important that if your ballast is failing, then you get it replaced or you maybe infor another very expensive light bulb very soon.

Hope that makes your issue somewhat clearer (pardon the punn)

Apr 14, 2008 | Hitachi CP-X960 Multimedia Projector

Not finding what you are looking for?
Optoma H30 Multimedia Projector Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Optoma Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2237 Answers

color wheel light...
color wheel light...

Level 2 Expert

138 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you an Optoma Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...