Question about Liftmaster, Chamberlain, Sears Door Bracket

1 Answer

The opener inside the garage works when you push the button, but the remote outside the garage door just keeps blinking once you put in the code

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 244 Answers

What model. Did you code the outdoor keypad? Hit learn button and code the keypad. If done correctly, light bulbs on motor head will blink once or twice.

Posted on Jul 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+: outside keypad will not open garage door at all bu...


The inside button is hard wired. The keypad is a small radio transmitter. If the battery in the keypad is good and it doesn't work when you put in the code it has probably just quit.

May 17, 2010 | Sears Craftsman LiftMaster Chamberlain...

3 Answers

HomeLink works in vehicle... unable to program hand held or remot


When did your remote and keypad quit working? Was it when you programmed the Homelink? It sure sounds like you have a bad logic board.

Jul 02, 2009 | Sears Craftsman LiftMaster Chamberlain...

3 Answers

Raynor garage opener-remote only works close up sometimes


check to seee if the little wire that hangs out of the operator is hanging out. This wire is the ant. if this is not the problem replace the 12volt battery you can buy them anywhere. make sure you didn't cut off the ant. wire (I have seen customers cut thios wire thinking its an extra and not needed or place the wire inside the box very little signal that way have to be very close)

Jun 05, 2009 | Building Materials

1 Answer

Garage door will only close with keypad code it will not open


UNPLUG THE UNIT AND WAIT 5 MIN.
WHEN YOU PLUG IT BACK IN CLAER ALL CODES BY HOLDING DOWN THE PROGRAM BUTTON FOR 20 SECONDS.
NOW TRY TO PROGRAM EACH REMOTE AND KEYPAD - IF THERE IS STILL A PROBLEM CHANGE THE BATTERIES AND REPEAT THIS PROCEDURE.

I HOPE THIS HELPS

Mar 31, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I have a Craftsman 315 remote door opener. Model 139.53753 I put in a new battery and now it's doesn't work. How do you code it again? Thanks, rr


Push and release the learn button on the back of the opener. It will be a square button. A little light will come on next to the opener. Then press and hold the button on the remote that you want to program if there is more than one button. The lightbulb on the opener will blink once. If there is not a lightbulb installed, you will hear a click.

Mar 05, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Wireless Keypad wont allow use of other door openers


hit learn button for 10 seconds. now nothing will work except wired buttons. Hit learn for 1 second and put in yur 4 digit keypad code and hit enter, light on motor will blink twice. hit learn again for 1 second and push button on remote. again bulb will blink. continue pushing learn for 1 second and adding another remote.

Dec 26, 2008 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Neither remote control will open door but wall mounted button wil


Make sure the code set inside the remote is the same as in the main reciving unit code.

Dec 06, 2008 | Sears Craftsman LiftMaster Chamberlain...

4 Answers

Sears Craftman Garage Door


I enrolled in the Assistant Premium Plan and am waiting on a response.

Apr 29, 2008 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Craftsman garage door remotes


push once the red button on the back, and then push the transmitter button u want to program u should hear 2 clicks inside the unit.. and if u dont.. hold down ur transimitter button .. the led in the back of ur unit should be blinking... otherwise let me know

Jan 13, 2008 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
Liftmaster, Chamberlain, Sears Door Bracket Logo

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top liftmaster Home Security Experts

kakima

Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

15557 Answers

Lawrence Oravetz

Level 3 Expert

9587 Answers

Are you a liftmaster Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...