Question about NAD 712

2 Answers

Nad 712 no sound

I bought a NAD 712 off craigslist. Unit powers on but there is no sound from the speakers.

I get sound from the speakers if input is connected to "main-in" - but no wounds if I connect it to any other input (cd, aux, ld etc).

Is this busted?

thanks,
-faroo

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,546 Answers

Check to see if one of the Tape Monitors is ON. Turn it OFF.

There's supposed to be a pair of jumpers between Pre Out and Main In. Are they there? If not, install a short RCA cable pair.

Posted on May 05, 2010

  • David Dunn
    David Dunn May 21, 2010

    Glad to be of help.

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The jumpers were the problem - the unit I bought did not have the jumpers. After reading your post I went back to the manual and sure enough there is one small line that states "In normal use these should be connected together using the links supplied."

I was supposed to go and return the unit to the seller yesterday and your post saved the day for me.

Thanks so much for the tip!!

Posted on May 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Connecting NAD 2600a amp.


Never connect incompatible connections. Speaker outputs are for speaker inputs. Period.

The various inputs on this or most any amp are for Line Level signal with the exception of anything explicitly labeled "PHONO" as that would be for a non-preamplified turntable ONLY.

From what I have found online, Lab-In was a NAD feature that restored the frequencies that were rolled off when turntables were being used in the (assumed) preamplifier that fed this amp.

http://web.295.ca/~peak//audio.html

"NAD belleived at the time that practical PHONO stages and the preamp and power amplifier stages be rolled off at subsonic frequencies to prevent subsonic wow and flutter from Turntables and supersonic frequencies (EMI/RF/Radio) signals from getting into the system in the first place. Their notion was that if your ears cannot physically hear it, then why amplify it. For the PURIST, there were a set of LAB IN amplifier inputs with more extended response called "LAB IN" inputs"

Use the Lab In's UNLESS you have a turntable source.

Aug 22, 2009 | NAD Audio Players & Recorders

1 Answer

Connecting NAD 314 Receiver\ preamp to Carver M-500t to speakers


Dear Tim,
Yes, you can connect your NAD as a preamp to the Carver power Amp.

Connect the NAD's pre-out to the input of the Carver Power Amp. You can then connect the Klipsch speaker to the Carver. Set the gain control on the NAD.

Now you should be able to control all the input and the main volume control from the NAD.

Mar 12, 2009 | Onkyo TX-SR803 Receiver

1 Answer

Will NAD 712 accept an iPod Docking Station?


A 712 is not set up to use an Ipod USB dock.  You can buy a dock that will use RCA jacks into an old stereo - Apple sells them, others too.  Then the Ipod sits up and you can look at it.  Or you can buy the 1/8" stereo plug to two RCA plugs that Radio Shack has been selling for 30-40 years, plug one end into your Ipod headphone jack, and run the two RCA plugs into your Aux input.  That costs about $5, and is easy as pie.  An Ipod will play through any old receiver, but the USB docks will not plug into them.

Dec 10, 2008 | NAD 712

2 Answers

NAD 7140


Hi okapi6

Use a 3.5mm stereo jack to RCA connector lead.
370a7a3.jpg Connect this to the AUX input on the back of the 7140, and away you go. Get the lead as an accessory from just about any electronics hobby store.

Dec 07, 2008 | NAD 712

1 Answer

NAD 7140


The clicking is the sound of a bad relay. A relay is an electrical switch that opens and closes under the control of another electrical circuit. There is no user solution for this. You'll have to take it to an electronics repair shop (~$150) or dump the whole unit.

Nov 22, 2008 | NAD 712

1 Answer

Nad c350 no power at all


check your output stage for bad speakers cable or bare wire of cable touch the body of amp----short circuit speaker cable----bad speaker it self------ bad input cable or defective input device .
disconnect all and check if it is ok---start to connect one by one from input to outputs------if all above failed you must contact service center for help.

Aug 22, 2008 | NAD C320 2-Channel Amplifier

1 Answer

NAD 712 Display unit


On my system the bulbs burned out some time ago. Today, I bought a pair of 12v micro lamps at Radio Shack (part 272-1092). Then removed the board behind the display and replaced the bulbs. This required some soldering. The bulbs have held up for more than 6 hours, so I do not think they are going to burn out.

Jun 04, 2008 | NAD 712

1 Answer

Nad 214 amp


problem is- intermittent speaker relay. You can cleaned contacts or better upgrade relay to better one (sealed)  Dariusz

Jan 03, 2008 | NAD 712

1 Answer

NAD 7140


Amplifier is about shot, need to replace IC pack or transistors (whichever it has). Could, remotely, be the speaker lines are installed incorrectly?out of phase. + to +, - to - from amp to speakers. Some amps will protect themselves when this condition occurs till fixed.

Aug 01, 2007 | NAD 712

1 Answer

Nad 712 output issues - Mute flashing


The only thing I can tell you for sure is that the mute indicator always flashes (very dimly) when the receiver is off.  I have no idea why, but mine has always done this.

Jan 23, 2007 | NAD 712

Not finding what you are looking for?

Open Questions:

See all NAD 712 Questions

NAD 712 Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top NAD Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5020 Answers

The Knight
The Knight

Level 3 Expert

73710 Answers

Larry Stiles
Larry Stiles

Level 2 Expert

287 Answers

Are you a NAD Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...