Question about KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

1 Answer

KitchenAid dishwasher pump-motor

My dishwasher stopped working. After troubleshooting it I found the pump-motor to be bad. I took it apart last week and ordered a replacement part. The only problem is, after leaving it apart for a week I forgot how to I took it apart. I know, but I am old so just look over me. Anyway can anyone tell me how to put it back together? The model number is: KUDM01FKSS1.

Thanks
Ben

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • KitchenAid Master
  • 1,150 Answers

Http://www.kitchenaid.com/webapp/wcs/stores/servlet/OCManualsLiteratureSearchResultView?catalogId=10552&langId=-1&storeId=10202

TRY THIS WEB SITE FOR A MANUAL. IF YOU CAN NOT GET THERE WITH THIS INFO:
http://www.kitchenaid.com/customer-service/manuals/
Go here and enter your model number. Worked for me.

Posted on Aug 05, 2017

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
praky16
  • 744 Answers

SOURCE: Kitchenaid custom 21 dishwasher will not turn on

Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...

thank u
rate me!!

Posted on Jul 27, 2009

  • 677 Answers

SOURCE: hello, our dishwasher has been leaving a film on

The problem is hard water and not your dishwasher. There is a new product out that will solve this problem once and for all. It is called the dishwasher filtration system. It is a small filter that goes under the sink and removes the hradness from your water before it enters the dishwasher. You will not have to worry about any clogged arms anymore and your dishes will look amazing. it is very affordable and works like a charm. get it at www.dishwasherfilter.com.

Posted on Nov 19, 2009

heatman101
  • 43501 Answers

SOURCE: My granddaughter has recently rented


Hi,
Check your heating element..


A bad heating element causes many problems in dishwashers…

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes


Posted on Sep 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher does not function properly


Best way to troubleshoot would be to use a multimeter and measure the electrical voltage at the pump just before the pump is to activate, watch the multimeter display for a drop in electrical voltage, if it does drop to zero the electronic control board located within the door has failed.

Dec 22, 2013 | KitchenAid Dishwashers

1 Answer

Frigidaire dishwasher model fdb1500fls2


Sounds like the capacitor on the motor is bad,

May 26, 2013 | Dishwashers

1 Answer

I have a kitchenaid KUDS01DJSS0 DISHWASHER THAT WAS MAKING LOUD WHINE NOISE..


you are better off getting a new dishwasher which is more water and elelectricity efficient. around 10 years is a good life and it will be putting good money aftger bad.

Jul 18, 2012 | KitchenAid Dishwashers

2 Answers

Dishwasher starts then pauses and drains.


Fixed! I had the issue where the cycle would start, the KUDS30IXBL8 would hum 4-5 times and then drain. Plastic folk pieces jammed in the disposer. These instructions took a few minutes (only 5 screws and a couple clips) to figure out how to take it apart, and it only took 60 seconds to put back together. How To Repair Dishwashers KitchenAid Repair Chopper Replacement

Apr 25, 2012 | KitchenAid Dishwashers

4 Answers

Kitchenaid Whisper Quiet + dishwasher making loud humming noise


Very likely pump motor shaft seal leaks water into bearing casing buildup of rust and consequently noise. I just replaced $112 worth of pump assy and it's back to normal. I would also buy repair manual for $10 on-line to be sure how to disassemble the sump to get to the pump.

Jul 14, 2009 | KitchenAid Dishwashers

3 Answers

I have a Fimco 2.1 gpm pump that worked fine last week. I ran it until it didn't spray anymore. This week the motor runs but it seems to have lost its prime,it won't pump.Any ideas? The filter is clean. No...


I don't think that these pumps run dry very well ... most likely you ruptured a diaphragm by running it dry. How long did it run dry? ... take it apart and see if the diaphragm or valves are damaged. You will need to replace them before the pump will work.

Jun 25, 2009 | Fimco Trailer Sprayer, 15 Gallon, 2.1 GPM,...

1 Answer

No incoming water


I have the same type problem. Does your control panel light as expected? If so, remove the lower cover at the floor and take a pencil or screwdriver and spin the impeller ( at the beginning of the cycle) of the water pump to see if it will take off and pump water. If it does, you'll hear the water flowing into the washer. This is where I am in my troubleshooting. Our dishwasher will complete the cycle with clean dishes. I'm not sure if the pump is bad or if there is a control circuit for the pump. Hope this will help.

May 03, 2009 | GE 24 in. Profile PDW9880JSS Built-in...

1 Answer

My whirlpool du1050xtps3 makes a grindin sound


Yes, this is common. Sounds like bearings in the motor. Will need to replace the pump and motor assembly. 14 6324 -->partimage.aspx?imgid=z3bqljbfahrfmduxntm1oc9mufcvc290b2hwdhjhcc8%3d
Enlarge Photo
Pump and motor assembly, complete - Original Whirlpool Part. Fits Whirlpool and KitchenAid dishwashers. This dishwasher pump and motor kit comes pre-assembled for easy installation.
Part Number: AP3778061 made by WHIRLPOOL $173.71 In Stock
Order now and it will ship Today
questionmark.gif This is the part with picture from http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5136316. Look in your owners manual because some models cover this part for 2 yrs. Hope this helps.

Nov 18, 2008 | Whirlpool 24 in. DU1100XTPS Built-in...

1 Answer

Maytag dishwasher MDB8600AWS


I have the same problem. I took the bottom sprayer assembly apart and found there is what Maytag calls a "seal kit" that has stripped threads. the part is plastic with a metal washer on the bottom and sits on top of the motor. To get to it, you have to remove the sprayer, shroud, pump housing and impeller. It is the part the impeller screws into, and may come out attached to the impeller.
I am have the part number as 99003341 and will be calling around for one later today. I will repost if this works.

Apr 24, 2008 | Maytag 24 in. MDB8600AWS Jetclean II...

Not finding what you are looking for?
KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Mike

Level 3 Expert

4340 Answers

Cindy Wells

Level 3 Expert

5160 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...