Question about Sony FD Trinitron WEGA KV-36HS500 36" TV

1 Answer

Problem for Sony FD Trinitron WEGA KV-36HS500 36

Problem for Sony FD Trinitron WEGA KV-36HS510 36" TV
Stand by light flashes 6 times
Ads by Google

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 100 Answers

ONE: Unplug it for at least 4 hours. That is what we call a hard reset.

TWO: If the hard reset does not help, then it will need further diagnostics.

The following bulletin may be of help in your learning about what is going on. Please refer to it below. Then let me know if you need further assistance.

Have a great day,
Cleggsan
========

Sony Blinking Codes
Many of the later model Sony TV's have a built in Self- Diagnosis function. If
the timer/standby indicator is blinking, this could be an indication of the
problem with the unit. The diagnostic blinking will occur automatically with no
action required by you to engage it.
The timing of the blinking you see would be as follows: two to eight blinks
(depending on the fault) about a third of a second apart, then pauses for 3
seconds, then the two to eight blinks about a third of a second apart again.
Here is a list of the problems that might have occurred indicated by the
number of blinks. The words in parentheses are those which you will see for
each of these faults on a diagnosis screen described later in this article.
Unit is dead and there are no blinks---Problem in the standby power
section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should
show open)
Continuous Blink Once A Second, No Pausing As Discussed Above---
No reply from the jungle IC301 (data bus is busy, shorted to ground or held
high), IK video path is defective.
ONE Blink--- not used for the self-diagnosis
TWO Blinks---B+ over current protection (OCP) , unit goes to the standby
mode then displays the 2 blink fault. Could be a short in the power supply of
any of the circuits.
THREE Blinks---B+ over voltage protection (OVP), unit goes to the standby
mode then displays the 3 blink fault. This is also a problem in the power
supply circuit, check T603 and R672.
FOUR Blinks---No Vert. Deflection (V STOP), Screen goes to a single
horizontal line then the video signal muted. Check IC1509, Q1505
FIVE Blinks---AKB circuit (AKB), the timer/standby indicator blinks for about
30 seconds then goes to the self-diagnosis function. Something is wrong with
the video. Check video out, Q705, 732, 761 and other components on the C
board, also check Q218, 219, 220 on the A board. Also unit be in IK blanking,
try turning up screen slightly.
SIX Blinks---No Horizontal (H STOP), no raster, goes to the blinking selfdiagnosis
function immediately. Check C515 & 516 and the jungle IC, IC206.
SEVEN Blinks---High voltage shutdown. The high voltage has exceeded 33k
and the unit goes immediately into safety shutdown. Check power supply
regulation and horizontal circuits.
EIGHT Blinks---Problem with the audio (AUDIO), unit goes to standby and
blinks the self-diagnosis code. Check IC406 audio amp, PS401 and 402.
Intermittent problems ?? This is a great feature. You can also bring up
these fault codes ON-SCREEN to see a list of the problem numbers with the
abbreviation of the problem and the number of times this problem has
occurred. This is slightly different than entering the service mode. To see the
diagnostic screen, Press the following buttons:
Display, Channel, 5, Vol Minus, ( Not plus ) then Power. This brings up
a screen with a list of the problems and number of times they have occurred.
Each of the problem names is abbreviated as, "OCP", "OVP", "V STOP", ETC.
We have repeated them in parentheses in the text for the "Blinks" described
above so you can correlate between the diagnostic screen and the blink
codes.
So, now that you know about these self-diagnostics, how do you use them?
Say that you have a set with a black screen. You see that the LED is blinking
4 times....This would tell you that you have no vertical and that is why the
video is muted. If it was blinking 6 times, you would know that you have a
horizontal fault.
It's not a sure cure, but it's a little better than a poke in the eye with a sharp
stick.
IMPORTANT: after you repair the unit, PLEASE clear the values on this
diagnostic screen. These codes do not reset themselves after the fault is
corrected, so if you don't clear them, you'll be seeing "old" fault codes the
next time you enter this screen.
Clearing is done by going into the service mode ( display, channel, 5,
volume plus, then power ) then press 8 and Enter, which of course returns
everything to the factory preset condition.

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sony FD Trinitron WEGA KV-34HS420 34" TV Stand by


I have the indentical tv and problem. Cost to repair was about 250.

Aug 19, 2011 | Sony FD Trinitron WEGA KV-34HS420 34" TV

1 Answer

Won't turn on.stand-by light flashes.timers are


my Sony trinitron kv-g21s2 TV not working . conned to the power blink in TV power indicator led

May 29, 2011 | Sony FD Trinitron WEGA KV-13FS100 13" TV

1 Answer

Sony FD Trinitron WEGA KV-32HS420 32" TV.....Turns


Sounds like a diode may have burnt up or if your really lucky it might just be the fuse.!!! You might want to get a secound opinion .But if you know what to look for , which is any component on the motherboard that appears as if had caught fire sader it out amd replace with exact same component which can be ubtained at radio shack.GOOD LUCK TOO YOU!!!!!!!!!

Dec 23, 2010 | Sony FD Trinitron WEGA KV-32HS420 32" TV

1 Answer

Sony FD Trinitron WEGA KV-30XBR910 30" TV Led flashing


6 blinks meens no horizontal and no raster check capasitor c515/c516/ jungle IC and IC206.
regards,
daniel.

Dec 28, 2008 | Sony FD Trinitron WEGA KV-30XBR910 30" TV

2 Answers

Sony FD Trinitron WEGA Standby Light Blinks, TV Does Not Turn On


Sony FD Trinition Wega KV-32HS510 Try to turn tv on -it starts then shuts off -stand by lights keeps flashing. Memory stick light flashes then goes off.

Nov 29, 2008 | Sony FD Trinitron WEGA KV-34HS420 34" TV

2 Answers

Sony trineton KV-34HS510


let me know how many times standby light flashes. this info will help me to assist you to resolve tv problem.

Sep 05, 2008 | Sony FD Trinitron WEGA KV-34HS510 34" TV

1 Answer

Sony FD Trinitron WEGA KV-36HS500 blinking red light 6 times


smack it on top a couple of times, it works for me :)
if ya cant duct it, smack it...
seriously...

Jun 29, 2008 | Sony FD Trinitron WEGA KV-32HS500 32" TV

1 Answer

Sony FD Trinitron WEGA KV-36XBR800 36" TV


I get a black screen after power on...then a bright white light in the middle of the screen.Then the red light flashing and turns it self off.

Oct 27, 2007 | Sony FD Trinitron WEGA KV-36XBR800 36" TV

Not finding what you are looking for?
Sony FD Trinitron WEGA KV-36HS500 36" TV Logo

747 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

kakima

Level 3 Expert

102366 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...