Question about Office Equipment & Supplies

1 Answer

Time to change PCU

I have changed the PCU in my Gestetner F9103.
Still getting the message "Time to change PCU"

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 159 Answers

You just have to press the "yes" button. Watch the display. It says "Change PCU Y/N"

Posted on Mar 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Even I change the tuner but it's appearse the same masseage to put a new ink or tuner


If the copies look fine it is the toner hopper. It does not remove the seal from the bottle when closed. If the copies are getting light it could be the developer unit has worn out bushings and gears thus it does not turn properly making it impossible to sense the toner level and the constant add toner message. Usually you can hear noise if this is the case. Look at the oriface where the toner drops into the photoconductor unit from the toner unit. Is it full of toner coming out the top? If so, time to replace the PCU.

Nov 01, 2013 | Gestetner DSm415pf Digital Imaging Sytem

1 Answer

@wAm getting a sc 302 code on a gestetner mp 171.I have changed the whole drum unit.


Hello!
When you change the PCU did you conect the blue plug????
If this is not the case remove the PCU again and if you look deep down you will see a metalic shaft. Clean it and install again the PCU.

Hope this helps you

Aug 01, 2011 | Ricoh Aficio 2015 Copier

1 Answer

I have a gestetner 1312 copier it says reset pcu proprly.what does this mean.


The PCU is the drum unit. It probably has just worked loose. Just unlatch it and shove it back in to make good connection in back.

Jul 27, 2010 | Gestetner Office Equipment & Supplies

1 Answer

My gestetner 2712 has ran out of toner. i have replaced the toner, the machine takes a while to load and then comes back with load toner again. Why would it not be registering a full toner bottle?


GESTETNER 2712 PROBLEM USUSALLY SIMILAR TO RICOH 2022/1022/27 PROBLEM IN WHICH INLET IN PCU AT LOAD TONER OUPUT. wHAT YOU CAN DO ,TEK OUT THE PCU IN CHECK IF THE PCU TONER INLET IS BLOCK EITHER BY SEAL OR DUE TO INLET CLOSER MALFUNCTION CAN BE REPAIRED IF YOU HAS EXPERIENCE OPENIG UP THE PCU

Apr 06, 2010 | Gestetner 2712 Digital Imaging System...

1 Answer

Hi.when i m switch on the Ricoh 3310L Fax,the message is coming as shown below "time to change PCU"


Order a new PCU from Ricoh. Power off the machine and replace the pcu.
If you try and cheat it it will run for a short while and then lock-up breaking some gears. Cheeper just to order a pcu. Check Ebay, i see alot of Ricoh supplies there.

Jan 23, 2010 | Ricoh 3310Le Fax Machine, FAX3310Le...

1 Answer

I have a gestetner DSm745e it keeps on poping out a code SC302 however i don't have a manual for it can you help me?


Charge roller current leak.The polling module detects a current leak of the charge roller.Check,clean or change the charge roller,verify the connection of the PCU,and verify the high voltage suplly board conectors.Turning the main power switch OFF and ON resets the SC code if the error is caused by incorrect sensor detection.

Nov 20, 2009 | Gestetner DSm745 Black and White Copier

1 Answer

Afficio 450 or gestetner 3245 calibration


Dev. Change Process

1. Check that Dev. unit has the lastest seals.
2. replace dev. material.
3. Dump dev.
4. add new dev. material.
5. Hand rotate the dev. unit 10 times.
6. reinstall the dev. unit into machine.
7. cover the toner inlet opening with a piece of paper
8. insert PCU unit.
9. turn the machine on.
10. When machine reaches ready -- enter SP modes and perform SP-2801 (2 times)
11. open the right cover of the machine. Cheat the right cover switch. Examine the drum as it rotates. Afew bands of toner and the ID pattern will be developed on the drum. The drum should be clean -- a slight dusting on the drum is OK.
12. Perform SP-3001 -- ID sensor initial setting.
13. ** Important** remove the PCU unit. Empty the toner from the PCU by sliding the shutter on the bottom of the PCU to the side and tapping the PCU.
14. reinstall the PCU.
15. Run test copies.

Pls rate -- thank you

Mar 02, 2009 | Ricoh Aficio 450 Copier

2 Answers

Ricoh 3310L Fax machine - 'Time to change PCU'


You need a new drum. Photoconducter unit. Cost about 140.00 I sell them or you can shop on EBAY

Aug 10, 2007 | Ricoh 3310Le Fax Machine, FAX3310Le...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

702 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...