Question about AO Smith 1 1/2 HP 115/230V 56C Replacement Motor

1 Answer

Need wiring diagram for 230 volt fr56j ao smith, mod. c58m2u11c6

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 426 Answers

Go on line

Posted on Nov 06, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 104 Answers

SOURCE: Wiring problem

There should be a diageram under the cover that covers the wires,

Or note the two terminals marked L1 & L2. These are for the 2 power source wires from the circuit breakers. The ground is a seperate terminal.

You should not be servicing this type of equipment if you do not know the answer to your question,

Good Luck and make sure this motor is GROUNDED

Posted on Mar 19, 2009

john224
  • 1378 Answers

SOURCE: Looking for a wiring diagram for an A.O. Smith

Thank you for posting your question here on Fixya.com.

That actually appears to be part of the serial number, not the part number at the end of your post. What are you trying to accomplish? With a description of your terminal board and the current wire arrangement I should be able to tell you what you need to know. Another option would be to contact us through our site at www.arrowmotor.net and send a picture of the board.

If this answer does not fix your problem, please comment with additional details prior to rating the answer. Positive feedback is appreciated once your problem is solved!

John

Posted on Mar 17, 2010

  • 248 Answers

SOURCE: I want to reverse rotation

I believe all you have to do is swap your two hot wires,that works for 3-phase but not sure on single phase

Posted on Oct 09, 2010

  • 8404 Answers

SOURCE: Need wiring diagram for AO Smith Motor. Model #

Remove the rear cover and take a look. Unless this is a very old motor, there will be an indicator on the tab that will tell you the information you seek.

Normally ... let me say again, normally, a larger motor will come default 220 while a fractional hp motor will be 110.

To be double sure, take your motor to your Professional Pool shop and ask them to have a look.

Posted on Jul 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need wiring diagram for BN34 motor 2 speed 1.5 hp 230 volt


Usually the wiring diagram is on the nameplat of the motor. I hope this helps.

Aug 16, 2011 | AO Smith 1.5hp Pool Pump Motor 2 Speed Ao...

1 Answer

My pool originally had a 2 speed AO Smith pump motor. Several years back it was replaced with an AO Smith single speed motor. I am replacing that motor with a new AO Smith single speed Centurion Switchless...


Is it going to run on 230V then? If so you would normally use red and black. The white wire should be a neutral and the ground wire is obviously ground.

Do you have a meter you can use to confirm the voltage between the wires? If you do you'll want to start with red and white since you seem to think black was not being used before. If the voltage reads 230 and the motor is set up for 230 then attach one wire to L1 and the other to L2...it will not matter which is connected where as long as one is on each terminal. Insulate the black and ground the ground lead to the motor ground screw.

If the voltage is not 230 between those two check between red and black. If that is the 230 then insulate white and put red and black to L1 and L2.

John

May 23, 2011 | AO Smith 2 hp 3450rpm 56C Frame 230 Volts...

1 Answer

I purchased a 60 gallon compressor from Lowes which has a 230 volt single phase motor,3450 rpm,15 amp. The model # of the motor is 7-194160. There is no wiring diagrm in the manual. I was wondering where I...


There may be a wiring diagram either on the body of the motor or inside the wiring terminal cover.
A.O. Smith can be contacted at 800-262-6484. If you do call, have pertinent motor info ready.

Nov 30, 2010 | AO Smith Air Tools & Compressors

1 Answer

Need to know how to put the wires in the right order on a AO Smith 5.0 56 spa pump red white and black


Red and Black should each be connected to the individual power legs, for 230 V operation. The white wire should be connected to ground.

Nov 25, 2010 | AO Smith 2 Hp Spl 3450rpm M56 Frame...

1 Answer

I want to reverse rotation on my A.O. Smith 120/230 volt single phase 1.5 HP motor. Catalog number B762


I believe all you have to do is swap your two hot wires,that works for 3-phase but not sure on single phase

Oct 07, 2010 | AO Smith 1 1/2 HP 115/230V 56C Replacement...

2 Answers

How to connect the Dayton Capacitor Start Motor to 230 volts ?


In the **********, the screws will be market L1 & L2. There will also be a jumper that needs to be connected between the 2 terminals for 230V.

Aug 28, 2009 | Dayton Permanent Split Capacitor Motor Fan

Not finding what you are looking for?
AO Smith 1 1/2 HP 115/230V 56C Replacement Motor Logo

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top AO Smith Plumbing Experts

Lawrence Oravetz

Level 3 Expert

9587 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Gil Shultz

Level 3 Expert

3368 Answers

Are you an AO Smith Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...