Question about Cameras

1 Answer

Mamiya 645 Super Replacement Parts

I need a replacement part, a locking pin (slotted at one end)for a Mamiya 645 Super Pro Power Winder.

Posted by on

  • danielw6820 Mar 26, 2008

    Thanks..I'll email them with my query.


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 667 Answers

You can probably order direct from Mamiya, here is the contact info: Mamiya America

Posted on Mar 26, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Screen read card locked ,will not allow to read cardunlock sd card

All SD cards has a physical switch that locks the card. Remove the card from the camera and check this switch. It's on the left side of the card opposite side the angled edge. Make sure that the switch is in the forward position (towards the pins that get seated in the camera). Replace the card in the camera carefully to avoid moving the switch. Try accessing the card again.

If the switch is damaged or slides back and forth to the locked position easily, replace the card. It's possible to temporarily fix the card to access it. You need to carefully cut the switch plastic away from that slot and then cover the slot with tape. Make sure that the tape lies flat against the card and doesn't cover the area with the pins.

I hope this helps.

Cindy Wells

Apr 27, 2014 | Samsung BL103 Digital Camera

4 Answers

Just got a 645= shutter "release jammed:, I put in new battery and also missing the crank arm, must have had a motor handle before. its like new, meter in prism works new battery,have old 645 J to...

if the shutter is jammed just off the device,and slightly pull the shutter door with your hand 3-4 times.apply a drop of oil on both the sides.and then on the device.and check it will work.
and for the replacement off the handle you will have to check on the old device that where are locks in the back you just have to remove that locks,also check for the hidden screws in the centre or back of the handle.which may be blocking it to be removed easily.


Oct 11, 2008 | Mamiya Cameras

1 Answer

Canon 30D had bent CF pin - power light remains on: replace cf pin slot or cf pin slot AND motherboard??? Please help!!

As hobby photographer, and retired electronics engineer, I hope I can help you.
first, you virtually never find any fuse in a camera. Sometimes they build in a diode, to prevent damage when someone puts in a battery, the wrong way around, but most of the time you even can't put in a battery the wrong way around. If in your camera a pin from the CF connector caused a shortage in the camera, the connector should be replaced, but sometimes this shortage can cause extra damage, because voltages can come on places that can't handle this. A chip can die. Only to find out, when you replaced the connector and try to switch on the camera again. If you try to find some pictures of the inside of a DSLR, you can see that the "board" actually is a flat cable, with tiny chips connected. It is almost impossible to replace the components on that.
I know Canon certified repair centres, deliver good jobs and have original spare parts. But you always can ask what it will cost in advance and decide if you want to go on.
On the site ifixit dot com you can see how to repair a camera. I'm not sure your camera is opened there too, but you can get an idea how it looks inside.
Although a 30D still makes good pictures, perhaps you should consider to start saving up for a new one?

Apr 04, 2014 | Canon EOS 30D Body Only Digital Camera

1 Answer

I just bought a nice used Mamiya twin lens C3 but the shutter is locked up. There is a small metal piece holding the shutter release from moving. Not sure how to un-lock, seams to be a safety device of...

The vertical shutter sliding lever gets locked if the film doesn't get advanced to the next frame, and the mode selector is set for single exposure. You can't trip the shutter unless you have film in the camera and you forward the film to the next frame. That should allow you to release the shutter with the sliding lever.

Mar 17, 2014 | Mamiya Cameras

1 Answer

Need a replacement back cover for my Mamiya 7ii. Where should I go in the UK?

please try here:

Aug 24, 2011 | Mamiya Cameras

1 Answer

Need replacement of direct interface cable - canon a-560 powersho

The required cable uses standard USB connectors. USB A male on one end and USB Mini-B 5 pin male on the other end. There are any number of sources to purchase one, here is an example.

Dec 24, 2009 | Canon Cameras

1 Answer

My d300 is showing r12 code how do i fix that

R12 is telling you that you have 12 pictures remaining in its internal buffer ... if it continues to show that then it is having trouble transfering to the memory card ... it is possible that you have a fake memory card or maybe a bad one (or ouch a bent pin in the camera) .. there are lots of fake cards around now ... if the card has worked in the past you might want to reformat it or check it on your computer .. unfortunatly its not hard to bend a pin inside your camera if the CF card is inserted wrong ... you can look in the slot with an led flashlight .. there should be no missing or bent pins ..

if you cant solve the problem then call :
Nikon Customer Service @ 1800-645-6689

Nov 23, 2009 | Nikon D50 Digital Camera

1 Answer

My Canon Rebel xti camera states that is an error with my compact flash, I bought a new one and it still won't work

Pull the cf card out and with a careful eye (maybe a small flashlight and magnifier) look down the slot and check to make sure none of the cF card receiving pins are bent... it happens and it'll give you a card error. Regretfully if this is the case, it'll need a repair, replacement parts are available but it is a little techie to get apart and swap parts... Check the pins... good luck on this..

Sep 08, 2009 | Canon EOS 400D / Rebel XTi Digital Camera

1 Answer

Memory Stick Will Not Engage

You need to replace the damaged memory slot with new one. If you know basic electronics and have tools for replacement, pls goahead.

Jul 26, 2008 | Sony Cyber-shot DSC-W55 Digital Camera

3 Answers

Canon 400D CF pin broken, power down

250 is a bargain if you value your time at anything over $10.00 per.
and canon will guarantee the results.
but...good luck

Aug 20, 2007 | Canon EOS 400D / Rebel XTi Digital Camera

Not finding what you are looking for?
Cameras Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cameras Experts


Level 3 Expert

98762 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

63456 Answers

Are you a Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides