Question about Sharp Audio Players & Recorders

Open Question

Hi. could u help me with my sharp cd ba 1500 hifi .? when i switch it on it displays protect on the screen and wont do anything els. ? what might be rong with it ? thanks

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: my audio system says protect on display

Hi Jean,

Without a brand and a model, best that I can provide are generic possibilities:
1. unplug the unit from the mains for a couple of hours. This is supposedly to reset most systems; and/or
2. check the speaker wires and make sure none of any bare wires are touching each other.

If your concern has not been corrected after completion of the above procedures, pls post back brand and model.

Hope this be of initial help/idea. Pls post back as requested, how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Feb 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My sharp cd-ba 1700,has protect on screen.how do i remove.thanks


The most common failure is of the internal Amp IC for these units. See the link below for a generic explanation of protect mode. I believe that the amp-pacs for these are still available and are in the $45 range.

Dan

Link: http://www.fixya.com/support/r5390728-protector_means

Oct 01, 2010 | Sharp Audio Players & Recorders

1 Answer

Sharp cd-bp1200w cd carriage will not open power is ok display ok . cds locked inside!


On my sharp CD-BA 1200 most cd's do not run. It is the problem that has recently occured. Kindly suggest solution.

Mar 14, 2010 | Sharp Multi-System Mini Component System...

1 Answer

Kenwood XD V757 System Protected


check the speaker wires are not shorting out

Dec 11, 2008 | Audio Players & Recorders

2 Answers

Sharp cd-dp2400 suitable remote contols


i have a sharp cd player and the speakers hook up to the cd player and they light up but when i plug in the speakers to play they wont play what should i do

Sep 03, 2008 | Audio Players & Recorders

1 Answer

PROTECT on start up


The protect message indicates that the output amplifier section has a problem and the unit has shutdown to prevent further damage. This usually is caused by shorted transistors in the final output stage. In your case, the output amplifier is a single replaceable amp-pac (STK402-090S). This can be purchased from tritronicsinc.com using the Sharp part number: VHISTK4029S-1 at a cost of $63.32

Dan

Jul 12, 2008 | Audio Players & Recorders

1 Answer

Protect push power


hi, everytime i switch on my sony hi fi it the display screen says protect push power. It won't let me do anything not even put cd's in. If you could help that would be very much appreciated.

Jun 12, 2008 | Sony LBT-XGR6 CD Shelf System

1 Answer

SHARP BA1700


Dear steve37,
Please switch off the system from the wall socket. Remove the speaker wires from the rear side of the system. power on the system if it works ,the speakers or the wires are defective.
ramesh22

Jun 08, 2008 | Sharp Audio Players & Recorders

1 Answer

Display read protected and wont do anything


Usually, protect mode is enabled when the speaker output wiring has shorted together or is touching ground/+12V. I would verify that none of the speaker wiring has come loose.

Mar 19, 2008 | Kenwood KDC-MP5032 - Car Audio CD MP3...

1 Answer

My audio system says protect on display


Hi Jean,

Without a brand and a model, best that I can provide are generic possibilities:
1. unplug the unit from the mains for a couple of hours. This is supposedly to reset most systems; and/or
2. check the speaker wires and make sure none of any bare wires are touching each other.

If your concern has not been corrected after completion of the above procedures, pls post back brand and model.

Hope this be of initial help/idea. Pls post back as requested, how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Feb 23, 2008 | Audio Players & Recorders

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

73611 Answers

 Grubhead
Grubhead

Level 3 Expert

5011 Answers

John
John

Level 2 Expert

509 Answers

Are you a Sharp Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...