Question about NRS Stex 8020T Treadmill

1 Answer

Treadmill Stex 8020 when switched on immediately increases speed on board (without touching buttons) until it reaches 250km...the belt isn't moving when this is happening and pressing + or - or other buttons will not stop the speed from increasing. Can your man please advise, thanks.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • NRS Master
  • 832 Answers

If it reaches 250km then I suspect that the upper electronics is not functioning properly contact the distributor of Stex and If under warranty they sould cover it,but send out a servicer

Posted on May 06, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stex treadmill about error 2


adjust the Speed sensor, see the diagram, clean it, test for open or faulty, and tight the connector very well.
Lube the deck belt, see the video, lube the rollers bearing front+back too , test the drive belt motor and replace the belt if necessary. God bless you
However you must try to Run the software calibration after your fix it.4d80cf2e-89d9-4476-902b-88e5991886e8.gif

Jul 03, 2013 | NRS Stex 8020T Treadmill

1 Answer

Life fitness 95t speeds up after confirming slower speed in cool down mode, and also pauses after touching increase button on screen. both issues are dangerous


book an engineer, sound like motor controller, loose belt could also be a issue, needs a safety check where are you based ?

Jan 27, 2013 | Life Fitness Exercise & Fitness

1 Answer

Proform xp 650 e 80 e 26 pluged in 1st time in about a year and got this code. Wont do anything????


I will try to help you: Please use patience+carefully and basic tools+Dvom. How to Troubleshoot a Treadmill


Although most home treadmills are designed for easy operation, there are some common problems that are inevitable. The console may not display. Perhaps a loose or slipping running belt poses a safety hazard. Maybe the treadmill runs at an unpredictable speed. Those are just some of the things that can happen to bring your workout to a halt. While certain repairs will require the services of a professional who specializes in treadmill maintenance and repair, there are some basic repairs that you can do yourself.

Difficulty:

Moderate
Instructions

1.

    • 1

Clean and routinely maintain the running belt. The belt may be worn if the treadmill stops operating or trips the circuit breaker. Look for any tears in the belt. Test the belt by putting the treadmill at full incline. If it does not shut off, you may need to replace the belt. You can try lubricating it first, but the safest fix is simply to replace it.

    • 2

Tighten the running belt if it is loose. A belt can slip if there is too much friction. Be careful not to tighten the belt too much, though. You should be able to lift the belt at least 3 inches.

    • 3

Push the belt in the direction that it normally turns. Turn off the power before you start. If the belt is difficult to turn, there is high belt/deck friction. However, if the belt moves freely, that's not the problem.

    • 4

Examine the roller sleeve to see if it is centered on the running belt. If not, this could cause the belt to move to one side. Often a common problem with treadmills, you can try making adjustments yourself, but eventually you may need to replace the sleeve or roller.

    • 5

Stop the treadmill and immediately unplug the power cord from the outlet if you notice a burning smell. Overheating could be a sign that there is too much friction or a short in the wiring. Examine the belt and deck for any signs of wearing. If they check out alright, inspect the wiring. Replace any damaged parts as needed.

    • 6

Check to make sure that the power switch is on if you suddenly lose power. If this isn't the cause of the power loss, unplug the treadmill from the wall outlet and individually test the fuses, breakers and switches. Test the wall outlet first, as a fuse may have blown or a circuit breaker tripped.

    • 7

Allow the treadmill to run at a speed of 2.5 mph without anyone walking on it if you notice fluctuations in the speed. The speed should be constant. If not, there could be a problem with the motor.

    • 8

Test the motor using a fully charged lantern battery. The motor should still operate at slow speed.

    • 9

Replace the batteries in the panel if it dims. If the batteries aren

Oct 22, 2011 | Exercise & Fitness

1 Answer

Error code 1


I am the same Problem with Stex 8020 T Error Code 1

Oct 25, 2010 | NRS Stex 8020T Treadmill

1 Answer

Belt just runs at max speed automatically :(


Yes. Replace the speed sensor. In the unlikely event that the problem still is not solved replace the circuit board. J.

Jul 31, 2010 | York Yankees Bedding MLB Comforter

1 Answer

Describe your Spirit ® XT275 Folding Treadmill Problem - serial number 90488105100032rev-00 I started the treadmill as I normally do by pressing the start button. The belt does not move. I think...


Hi

Thanks for using FixYa. Please read this out:

How to Troubleshoot a Treadmill

If still the issue is not resolved then you can contact local repair center.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks

Rylee

Jan 05, 2010 | Spirit ® XT275 Folding Treadmill

1 Answer

Pro-Form Sport 1000 treadmill does not stop inclining


Do a Calibration on the treadmill. Take out the safety key. With 2 fingers, hold down the stop button and the speed up or spped plus button. keep holding them down as you insert the safety key, then let go of both.
Press the stop button 1 time, you should see all 0's in the windows, or EP 2P or something weird like that.
Press the Incline up button and then wait. If the incline go up until it stalls then down until it stalls the stops at the bottom, the you are recalibrated, take out the safery key and put it back in to see if all is well. If the incline takes off up again without touching a button, the you have wiring problems or control problems. Call service company to get it repaired.

Apr 27, 2009 | Proform Sport 1000 Folding Treadmill...

Not finding what you are looking for?
NRS Stex 8020T Treadmill Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top NRS Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

33339 Answers

Are you a NRS Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...